Search: Posts Made By: PJmax
Showing results 1 to 25 of 200
Search took 0.01 seconds.
Replies: 11
Views: 248
Posted By PJmax

Thanks for stopping back and letting us know how...

Thanks for stopping back and letting us know how you made out. :thumbup:
It's very important for people accessing threads like this for help.
Today, 05:00 PM
Replies: 10
Views: 147
Posted By PJmax

Good and helpful video....... Flame out @ 1:42....

Good and helpful video.......
Flame out @ 1:42. Board fault LED shows as normal. That means no limit faults.
Igniter reheat attempt @ 1:57. Gas valve clicking at 2:02 but no flame
Igniter reheat...
Replies: 12
Views: 557
Posted By PJmax

I can say one thing.... this thread is a good...

I can say one thing.... this thread is a good reason to NOT get a Toto toilet.
Replies: 10
Views: 138
Posted By PJmax

I'm in a cold zone here in NJ. I have 6' + of...

I'm in a cold zone here in NJ.
I have 6' + of ice shield. I consider it insurance.
Today, 02:20 PM
Replies: 5
Views: 102
Posted By PJmax

I'm a little concerned. Exit lights are used in...

I'm a little concerned. Exit lights are used in commercial applications and you should not be involved in a commercial installation.

UK wire sizes are different than we use. You need to consult a...
Replies: 9
Views: 131
Posted By PJmax

All that came with the appliance..... awesome. ...

All that came with the appliance..... awesome. :thumbup:
Typically a service manual needs to be purchased.

I'll check out what you've posted.... thanks.
Replies: 10
Views: 138
Posted By PJmax

Based on CT codes..... the minimum is 36" of rain...

Based on CT codes..... the minimum is 36" of rain shield.
I'd want 6' in place.
Replies: 2
Views: 49
Posted By PJmax

I'm guessing those are CVPC lines. I'd replace...

I'm guessing those are CVPC lines.
I'd replace them with flex lines.
Today, 02:00 PM
Replies: 4
Views: 36
Posted By PJmax

With a three phase motor.... the compressor is...

With a three phase motor.... the compressor is designed for commercial/industrial use.
#12 is the minimum size used in that application.
You can install a 1/2" or 3/4" flexible conduit.

Since...
Today, 01:52 PM
Replies: 5
Views: 51
Posted By PJmax

Welcome to the forums. The ID tag is inside...

Welcome to the forums.

The ID tag is inside on the side wall near the burner behind the burner access door.
There is a control board down in the blower section that has a fault LED on it.
You...
Today, 10:16 AM
Replies: 6
Views: 90
Posted By PJmax

https://cimg5.ibsrv.net/gimg/www.doityourselft.com...

https://cimg5.ibsrv.net/gimg/www.doityourselft.com-vbulletin/456x237/bathw_c_4eb976a6b23f9ac730593f58ef9d0e41d2b54791.jpg
...
Replies: 3
Views: 91
Posted By PJmax

It's either for a bathroom fan or a dryer. Looks...

It's either for a bathroom fan or a dryer. Looks clean which would suggest bathroom.
Turn on the fan and blow the bird out. :eek: .................:EG:

Just kidding. Your going to...
Replies: 9
Views: 131
Posted By PJmax

if you put the unit in bake...... either the bake...

if you put the unit in bake...... either the bake or the broil element could come on during warmup.
That means you should get 240v on either of the two elements.
I believe.... once operating temp...
Replies: 9
Views: 144
Posted By PJmax

WB26X10134 circulating blower. Black = hot/high...

WB26X10134 circulating blower.
Black = hot/high speed.
White = hot/low speed.
Red & yellow = 10uf capacitor.
Blue = neutral.

Use a voltmeter and see if you get high and low power..... black or...
Yesterday, 05:39 PM
Replies: 4
Views: 62
Posted By PJmax

There is more than one limit switch. The manual...

There is more than one limit switch. The manual shows three.
Flame rollouts and limit.

It sounds like you have a blower problem.
If the blower doesn't run the unit will shut down on overheat.
...
Yesterday, 04:53 PM
Replies: 6
Views: 64
Posted By PJmax

Since you've replace the igniter it points to the...

Since you've replace the igniter it points to the board.
I fully troubleshoot because customers don't like paying for an un-needed board.
Yesterday, 04:49 PM
Replies: 10
Views: 147
Posted By PJmax

Sorry.... I didn't read all your testing. I did...

Sorry.... I didn't read all your testing.
I did look at the video.

What do you have for a thermostat ?
Do you have a piece of wire with alligator clips ? (Very handy to have)...
Yesterday, 04:35 PM
Yesterday, 04:34 PM
Replies: 6
Views: 64
Posted By PJmax

Then you don't have a high heat fault. The...

Then you don't have a high heat fault.

The furnace follows logical steps.
Each step must be verified before ignition can start....
Replies: 9
Views: 144
Posted By PJmax

WB01X10132 GE Microwave mounting bolt 1/4-28 X...

WB01X10132 GE Microwave mounting bolt 1/4-28 X 3-3/4"

Which fan on which unit. :confused:
Yesterday, 04:14 PM
Replies: 8
Views: 94
Posted By PJmax

If turning a burner valve on fails to start the...

If turning a burner valve on fails to start the spark process anywhere.... the switch(es) are most likely bad. As I mentioned previously.... if the switch is bad the spark module may try to relight....
Yesterday, 02:32 PM
Replies: 6
Views: 90
Posted By PJmax

Welcome to the forums. If this is new...

Welcome to the forums.

If this is new work..... use two switches. One for light and one for fan.
Run your 12/2 w/ground feed to the GFI receptacle.
Run a 12/2 w/gr from the GFI to the switches....
Yesterday, 02:16 PM
Replies: 7
Views: 91
Posted By PJmax

You can use 1/8" x 2" long toggles. ...

You can use 1/8" x 2" long toggles.
https://cimg2.ibsrv.net/gimg/www.doityourselft.com-vbulletin/274x178/1_8_toggle_e6d314ccf9841143e7d5892e4a05c74d91fe21cd.jpg


1/8" x 2" toggles - mushroom...
03-26-24, 12:44 PM
Replies: 4
Views: 62
Posted By PJmax

Welcome to the forums. Fault code 33 is an...

Welcome to the forums.

Fault code 33 is an opening high limit or flame rollout switch.
When any of those switches opens..... the 24v power to the thermostat is cut and typically the blower and...
Replies: 3
Views: 103
Posted By PJmax

Welcome to the forums. Many of these systems...

Welcome to the forums.

Many of these systems can be defaulted to a default code on power up.
I'm not familiar with this system.

On the first page of the programming manual it tells you how to...
Showing results 1 to 25 of 200
 


 
Forum Jump