Roofing 9 - Shingles Roofing 9 - Shingles

Applying Asphalt Shingles

Composite (asphalt) or fiberglass shingles is the most common roofing now in use. It is composed of asphalt impregnated paper with mineral granules coating the exposed surface. Numerous colors and styles are available to enhance the design of your garage. Shingles are easy to install, require little maintenance and are easy to repair.

Flash Player You should get Adobe Flash Player so you can view our video.


Wind sealed shingles have an added dab of roofing cement under the bottom edge of each shingle. After these are installed and the roof is heated by the sun, the cement melts and sticks to the shingle below, increasing their effectiveness in high wind areas or on shallow sloped roofs.

Most Common Mistakes:

  1. Leaving out the starter strip.

  2. Not keeping shingles aligned.

  3. Not overhanging shingles at eaves and rakes.

  4. Neglecting to stagger joints.

  5. Installing ridge shingles before hip shingles.

  6. Neglecting to keep hip and ridge shingles in a straight line.

Construction:

  1. If you are using a drip edge, the starter course goes on TOP of the drip edge at the eaves (bottom) and UNDER the drip edge at the rakes (sides). The starter course applied at the eaves is a standard row of composite asphalt shingles with three inches cut off the tab (bottom) ends. (You could also use a 9 inch wide strip of roll flooring.) These are installed in an inverted position. The tabs face the ridge, the wind seal is down, and the mineral surface is exposed to the weather.

  2. Overhang the eave by 1/2 inch and leave a space of 1/16 inch between each shingle. Nail each starter shingle with four 12 galvanized roofing nails placed three inches above the eaves - one inch and twelve inches from each end of the shingle.

  3. The first full size course of shingles is installed DIRECTLY ON TOP of the starter course but with the tabs facing down towards the eaves. Nail the first and subsequent courses using four nails per shingle, placed 5 and 5/8 inches above the butt or bottom line (5/8" above the top of each cutout). Again, drive a nail one inch and 12 inches from each end.

  4. To prevent the shingles from buckling, begin nailing each shingle from the end next to the previously laid shingle. Leave a gap of 1/16" between shingles. For the remaining courses, we recommend popping a vertical chalk line on the roofing felt every 36 inches and a horizontal chalk line every 10 inches. This will enable you to align the top and side edges of each shingle along a straight line.

  5. The joints between the tabs must continue to be staggered. This means the joints (cutouts) must not be aligned in adjacent courses.

  6. To do this, cut 6 inches off the first shingle of the second course at the rake (side) of the slope. Cut 12 inches (one full tab) off the third course, 18 inches off the fourth course, 24 inches (2 full tabs) off the fifth course, and begin the sixth course with just a 6 inch length of shingle. Repeat this sequence beginning with a full length shingle on the 7th course.

  7. Once the flat planes of the roof have been shingled, you will need to apply the hip shingles, if you have a hip roof, which will be overlapped by the ridge shingles. Gable roofs will only have ridge shingles. These can be purchased prefabricated or can be cut from standard shingles - one 12 inch tab from a standard shingle, folded in the middle as shown in.

  8. Pop chalk lines 6 inches on each side of the hip and/or ridge centerlines. These will be the guidelines for the edges of the shingles.

  9. Start at the eaves of the hip, with a double layer of shingles, and work your way up to the ridge using the standard 5 inch exposure. Nail once on each side, 5 and 1/2 inches above the butt of each shingle. Where the hip intersects at the ridge, cut 4 inches up the center of a tab and nail this so that the uncut portion is nailed to the ridge and the 4 inch slit overlaps and is nailed to the top of the hip, covering the last of the hip shingles.

  10. Begin applying the ridge shingles at the ends, working each end toward the center nailing a saddle tab where they meet. Nail the saddle in all four corners.

  11. Cover any exposed nails with roofing cement and you are finished.

Got a New Project You're Proud of?

Post it on Your Projects!