DoItYourself.com Community Forums > Interior Decorating, Design, Painting, Upholstery and Fabrics Center > Architecture Plans and Structural Designs

Attic Access

Thread Tools

Search this Thread

08-30-05, 03:06 PM

Joe.Carrick

Member

Thread Starter

Join Date: Jan 2005

Location: United States

Posts: 437

Upvotes: 0

Received 0 Upvotes on 0 Posts

Attic Access

What's the minimum size for an attic access (UBC) ?

Upvote

08-31-05, 08:04 AM

Doug Aleshire

Member

Join Date: Feb 2002

Location: United States

Posts: 4,455

Upvotes: 0

Received 0 Upvotes on 0 Posts

Joe,

22"x30" Rough frame opening - 30" minimum unobstructed headroom

If mechanicals are in attic, that is another issue.

Hope this helps!

Upvote

Thread Tools

Search this Thread

Show Printable Version

Email this Page

Architecture Plans and Structural Designs
Interior Wall...sticky situation

S

shep68 on Aug 08, 2005

On the advice of several "experts" I began building an interior wall without a permit. It is non-load bearing and involves no electrical or plumbing. The "experts" said, "no permit necessary." Now it seems my problem is two-fold: 1. I need a permit but have already started construction (framing only no drywall.) 2. (This one is a doozy...) Upon removing the existing drywall and carpet I discovered the remnants of an existing wall (approx. 2 1/2' long) that appears to have been load bearing. Further increasing the idiot factor, I decided to continue framing anyway. At this point I discovered the unsupported truss appears to have sagged about 1 1/4 inches due to the lack of support. What is my best course of action at this point? I need to pull a permit for the work but it is already partially framed (and obviously not to code as I was not anticipating it being load bearing.) I also need to address the sagging truss. I'm certain the removal was done without a permit. I can't imagine the plans even being approved for such a project. Should I pull a permit and proceed as if I'm unaware of the issue and THEN bring it up once I have the permit? Should I come clean with code enforcement and risk substantial fines? I've documented most of the demolition and construction with photos and I'm wondering if those would work in my favor or against it. At the very least I can prove I didn't remove the load bearing wall. Any suggestions would be most appreciated. I'm confident this was a load bearing wall because: It appears to have been supporting the only truss that runs the entire span of the house unsupported (30' 10")Read More
Architecture Plans and Structural Designs
Minimum Hallway Width

T

thebeave on Aug 26, 2005

Hi, I just bought a house and am in the process of planning out some remodeling that I'd like to do. In the present house layout, access to the attached 2 car garage is via a "back door" from through either of two kids bedrooms, rather than directly off a hallway. Yes, I know that's a strange design. What kid wants their parents going through their bedroom in the morning to get to the car in the garage, or to do the laundry? Anyway, what I'm thinking of doing is making a new hallway 90 degrees from the existing hallway (which is in front of the bedrooms), by knocking out the 24" wide bedroom closets that are between the two bedrooms, and constructing a new, partition wall. Hopefully that makes sense. My basic question is: What is the minimum hallway width I can get away with, both from a code point of view and from a desirability point of view? Obviously, I'd like to minimize the width as much as possible, as it "eats" into already tight bedroom space. But I also don't want an unacceptably narrow hallway. I'm assuming there must be a fire door (20 minute?) between the garage and the new hallway. Are there minimum fire door widths? This requirement may determine the width of my hallway. Any help you can provide would be great. Thanks!! jamesRead More

Ask a Question