DoItYourself.com Community Forums > Interior Improvement Center > Basements, Attics and Crawl Spaces

Replacement motor for a Clark United Attic Fan

Thread Tools

Search this Thread

09-16-10, 05:42 AM

mdguy

Member

Thread Starter

Join Date: Sep 2010

Location: usA

Posts: 1

Upvotes: 0

Received 0 Upvotes on 0 Posts

Replacement motor for a Clark United Attic Fan

I have an attic fan with a Clark United corp model R-26, 3.4 amp motor. Clark United seems to have been bought out and are not doing business under that name. Anyone have any what a compatible replacement would be? Many Thanks in advance!

Upvote

09-16-10, 03:33 PM

Just Bill

Member

Join Date: Oct 2006

Location: Wilmington

Posts: 3,994

Upvotes: 0

Received 0 Upvotes on 0 Posts

Whole house fan , attic(roof mount), gable mount???? If whole house fan, take the motor to a local motor shop to seek a replacement. For others, just go to big box or lumberyards and buy a new fan unit. If the motor fits you unit, use it, otherwise replace all components.

Upvote

Thread Tools

Search this Thread

Show Printable Version

Email this Page

Basements, Attics and Crawl Spaces
motorless sump pump

F

frankieromance on Aug 31, 2010

just saw this in a magazine. what r your thoughts on this n can u explain how this works? a little confused. [url=http://www.basepump.com/Basepump.htm]Basepump|The water powered backup sump pump|Use water to pump water![/url]Read More
Basements, Attics and Crawl Spaces
Finishing Formerly Wet Basement ?s - Vapor Barrier/Moisture Alarm/Lighting

K

kmjcpa on Aug 14, 2010

When I bought my house, had no clue what I was in store for. The short of it is, I live in VA and now have two sump pumps in diagonal corners. They are both tied into the same system and one is on a battery backup. I also have two dehumidifiers. They are both turned off, the humidity goes up to ~50%. With them running, it drops to 30%. Additionally, before I regraded the landscaping and re-did the gutters and downspouts, one of the basement walls had efflorescence (i.e., water pock marks) and bowing. To address the bowing, we installed carbon fiber straps. Since then, the bowing has not gotten worse and we have not seen any efflorescence (even through Snowmageddon). So I think the water issue is "under control." However, I am now concerned because we plan to finish half the basement, so air will not continuously move throughout the basement. Based on this, I have a few questions (sorry if I am so long-winded): 1. When I do the framing, should I put a vapor barrier on the back of the framing? I have read mixed reviews, some suggesting it to protect the drywall and others against it because it will prevent the water from inside the room from escaping (not sure how much sense that makes because we will be tying the room to the HVAC system) and will encourage mold to grow between the outer wall and the framing. Any thoughts? If I should use a vapor barrier, any thoughts on what it should be? I heard of visquin but am not sure what it is or where to get it. Should I apply DryLok to the walls before I have the framing? 2. One of my friends suggested I put a moisture alarm in the wall behind the drywall, so I would know if there is a moisture issue. My concern is what good is that going to do me. I guess it is good to know, but that just means I will need to pull out the drywall. Should I build in an access panel so I can have access to this alarm? Has anybody done this? Any thoughts? 3. For the insulation, should it be faced/unfaced/contained in the plastic bags? 4. For lighting, I am highly considering recessed lighting, but am concerned about the number of cams I will need. The area will be used as a play around for my kids, so it doesn't need to be library bright, but still bright. The ceiling height is 8'. The area is composed of two different "zones." One is 26' x 12.5' and the other is 17' x 12'. Any suggestions on the number of cams and type? Or should I go fluorescent? If fluorescent, how many? (I posted this in the lighting section and currently have 42 views and no replies :() 5. Lastly, for the flooring, is there certain padding that is recommended for a semi-wet basement? I am still planning on having a de-humidifier running in the finished portion and it is tied to the sump pump, but I was not sure if there is a certain thickness that I should try to achieve. Sorry for all of the questions. I'm a little over my head by I think I will be able to get through this with everyone's help. Thanks in advance. KevinRead More

Ask a Question