Problem with retrofit recessed LED lights

Reply

  #1  
Old 04-20-17, 10:23 AM
Member
Thread Starter
Join Date: Nov 2009
Location: NJ
Posts: 57
Received 0 Votes on 0 Posts
Problem with retrofit recessed LED lights

I have older (late 80s?) recessed lights in the kitchen with the regular bulb and snap on trim. I would like to replace those with LED retrofit lights but it looks like all available sets are not wide enough to cover the "lip" of the casing. It looks bad to have one ring on top of another with the casing sticking out. Isn't there a way to cover those? I literally tried all available lights in Home Depot and Lowes. None of them have diameter that will cover old casings.Name:  light.jpg
Views: 343
Size:  16.4 KB
 
Sponsored Links
  #2  
Old 04-20-17, 12:36 PM
pcboss's Avatar
Forum Topic Moderator
Join Date: Jul 2002
Location: Maryland
Posts: 14,909
Received 24 Votes on 20 Posts
There are plenty of 5 and 6" retrofit LED's available. What size is your light?
 
  #3  
Old 04-20-17, 12:44 PM
Member
Thread Starter
Join Date: Nov 2009
Location: NJ
Posts: 57
Received 0 Votes on 0 Posts
This is a 6 inch light. Home Depot and Lowes usually carry universal 5 and 6 in combined replacements. All of those have diameter that's about the same or little smaller that my casing.
 
  #4  
Old 04-20-17, 03:16 PM
Tolyn Ironhand's Avatar
Group Moderator
Join Date: Nov 2007
Location: Twin Cities, MN
Posts: 12,933
Received 53 Votes on 46 Posts
That looks like a heat lamp to me. It also appears to be a can housing and trim on one. Pull down on the trim and see if it is held in by springs. If it is what I am thinking of the socket housing will be attached to the end. Look at the label in the can for a model name/number.
 
  #5  
Old 04-21-17, 07:11 AM
Member
Thread Starter
Join Date: Nov 2009
Location: NJ
Posts: 57
Received 0 Votes on 0 Posts
Here are more photos of the recessed light I have. The last photo shows Phillips retrofit LED light installed. You will see that the light doesn't cover the casing's rim. The outer rim of the case is 7.5" and the inside opening is 6 3/8".

Name:  20170420_195811.jpg
Views: 227
Size:  15.1 KB

Name:  20170420_195829.jpg
Views: 280
Size:  11.8 KB

Name:  20170420_200211.jpg
Views: 217
Size:  8.5 KB
 
  #6  
Old 04-21-17, 08:47 AM
Member
Join Date: May 2015
Location: USA
Posts: 3,138
Received 1 Vote on 1 Post
What's the diameter of the hole when the can is pulled out?
 
  #7  
Old 04-24-17, 08:09 AM
Member
Thread Starter
Join Date: Nov 2009
Location: NJ
Posts: 57
Received 0 Votes on 0 Posts
The diamater of the hole in ceiling is 6 3/4". Sorry for a late reply but my kids broke my laptop so I couldn't reply from home over the weekend.
 
  #8  
Old 04-24-17, 06:07 PM
Member
Join Date: May 2015
Location: USA
Posts: 3,138
Received 1 Vote on 1 Post
Perhaps you could use something like this:

https://www.amazon.com/szwintec-Ultr...g%2Blight&th=1

That particular model has to be wired into a box, but doesn't mount to the box. We can't see the end of the mc whip on your can, but it must go to a junction box that you could connect the driver to.
 
  #9  
Old 04-25-17, 03:36 PM
Tolyn Ironhand's Avatar
Group Moderator
Join Date: Nov 2007
Location: Twin Cities, MN
Posts: 12,933
Received 53 Votes on 46 Posts
I would not recommend that light Carbide posted as it is cool white (5000K)

As I suspected it is can/trim in one, like they use in commercial work.

IMO - it doesnt look bad with the extra ring around the trim. If you do not like I would get a remodel 6" can, move the wiring to the new can and insert it in the hole. I have done this in the past and the spring fingers grab the remodel can housing quite well. Then install your LED trim.
 
Reply

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Thread Tools
Search this Thread
Display Modes
 
Ask a Question
Question Title:
Description:
Your question will be posted in: