DoItYourself.com Community Forums > Electrical, AC & DC. Electronic Equipment and Computers > Lighting, Light Fixtures, Ceiling and Exhaust Fans

What type of light bulb is needed

Thread Tools

Search this Thread

09-22-17, 07:31 AM

skinut2234

Member

Thread Starter

Join Date: Dec 2004

Location: NJ

Posts: 279

Upvotes: 0

Received 0 Upvotes on 0 Posts

What type of light bulb is needed

what the heck kind of bulb goes in here?

Attached Images

Upvote

09-22-17, 08:02 AM

CircuitBreaker

Member

Join Date: Jan 2009

Location: United States

Posts: 1,028

Upvotes: 1,001

Received 77 Upvotes on 72 Posts

A GU24 CFL or LED energy saver

Upvote

Thread Tools

Search this Thread

Show Printable Version

Email this Page

Lighting, Light Fixtures, Ceiling and Exhaust Fans
Three way switch with ceiling fan issue

S

spudhead on Sep 18, 2017

Thanks for taking the time to read. I have been reading the answers to previous questions similar to mine. They don't seem to quite fit my situation, but everyone is so helpful I decided to post my question. I have a ceiling fan with pull switch chain controls that are a bit inconvenient to reach. Operating this fan are two switches, one at each side of the room. The switches are basic on/off toggle light switches and just kill the power to the ceiling fan or turn it on to whatever the pull strings have it set to. I have replaced one light switch with a Westinghouse 7787500 wireless ceiling remote wall control. The installation instructions are here: [url]https://www.manualshelf.com/manual/westinghouse/7787500/instructions-assembly-french.html[/url] Coming out of the wall are a red, black and white wire. There's also the copper, I think, ground, tucked in there too. The Westinghouse unit has two black and one green (ground) wire coming out of it. Currently, I have the wall red and wall black going to the Westinghouse blacks. The wall white goes to the Westinghouse green. I am confident I installed the receiver in the ceiling fan correctly as it was simple, and the colours matched perfectly too. As it is, the setup is working well-ish. Unfortunately, well-ish with electrical is not good! On occasion the breaker will blow. It used to only blow when using the untouched wall switch. However once it blew on it's own. And curiously, it only seems to blow when I've put all the Westinghouse wires back in the junction box. I've never had an issue before I've tucked it all away. The junction box isn't metal, my wire nuts are perfect and I also had someone look at it and they agreed it looks correct from a connections standpoint. I believe the issue is the load because of the three way switch configuration and the way I have it wired. I'm happy to call an electrician if this isn't something simple I'm missing. I'm also happy, and quite frankly now do want to add another Westinghouse controller to the other switch. Will this fix my breaker issue? The breakers are 15 AMP. Otherwise I can restore the toggle switches and buy a remote control which is less desirable. Sorry for the long post, I just wanted to explain as much as possible for any helpers. If you need photos or something or something isn't clear, please ask!Read More
Lighting, Light Fixtures, Ceiling and Exhaust Fans
Is this ceiling fixture box suitable for a ceiling fan? Or how do I replace it?

R

richpodraza on Sep 22, 2017

I have replaced several light fixtures with ceiling fans in my house using an "old work/renovation" brace similar to this: [url=http://www.homedepot.com/p/15-5-cu-in-Retrofit-Ceiling-Fan-Saf-T-Brace-0110000/204845572]15.5 cu. in. Retrofit Ceiling Fan Saf-T-Brace-0110000 - The Home Depot[/url] Then I went to replace a third, and the box I found when I took out the light fixture was different than the others. When I took all the screws out, the box remained secured in place. When I push/pull on it, it seems like it is attached to a joist from the side. At this point I am not really sure what to do. Since this box is secured to a joist, can I just use it to support the ceiling fan? If not, how do I get it out? I don't see any more visible screw heads. [url]https://photos.app.goo.gl/NBUq2Z2mK45DWMG13[/url] If I need to somehow get it out and replace it, I am assuming that renovation brace I linked above would not work, there would not be any drywall for the legs to rest on while tightening it. Do I need a different kind of box? Thanks! RichRead More

Ask a Question