Converting 2x2 and 2x4 fluorescent lighting to LED

Reply

  #1  
Old 09-08-18, 06:32 PM
L
Member
Thread Starter
Join Date: Oct 2015
Location: USA
Posts: 34
Received 0 Votes on 0 Posts
Converting 2x2 and 2x4 fluorescent lighting to LED

I just purchased a home with a finished basement with a suspended ceiling. The lighting is the traditional fluorescent 2x2 and 2x4. Is there an easy way to convert to dimmable leds without replacing the entire troffer?
 
Sponsored Links
  #2  
Old 09-08-18, 06:39 PM
PJmax's Avatar
Group Moderator
Join Date: Oct 2012
Location: Northern NJ - USA
Posts: 57,791
Received 934 Votes on 871 Posts
It's easy to just install LED replacement tubes. However, the dimming part is not quite as easy.
It can be quite experiment to find a dimmable replacement LED tube.
 
  #3  
Old 09-08-18, 06:41 PM
L
Member
Thread Starter
Join Date: Oct 2015
Location: USA
Posts: 34
Received 0 Votes on 0 Posts
How about a LED troffer retrofit kit?
 
  #4  
Old 09-08-18, 06:42 PM
PJmax's Avatar
Group Moderator
Join Date: Oct 2012
Location: Northern NJ - USA
Posts: 57,791
Received 934 Votes on 871 Posts
I've done a lot of conversions but haven't found a tube that dims well.
Many claim dimmable but work poorly.
 
  #5  
Old 09-16-18, 04:49 AM
L
Member
Thread Starter
Join Date: Oct 2015
Location: USA
Posts: 34
Received 0 Votes on 0 Posts
Circling back on this... so can I simply replace the current tubes with an LED tube? It doesn’t have to be fully dimmable. I was hoping I could just increase/decrease the intensity a bit.
 
  #6  
Old 09-17-18, 04:59 AM
P
Group Moderator
Join Date: Mar 2003
Location: NC, USA
Posts: 23,052
Received 533 Votes on 490 Posts
Yes, there are LED bulbs that you simply install in place of the fluorescent bulb. These bulbs still rely on the fluorescent light ballast so they are not as energy efficient and you still have the ballast as a point of failure.

When converting to LED's I like to get line powered bulbs. You re-wire the fixture removing the ballast and send 120 VAC directly to the bulb according to the bulb's instructions.
 
  #7  
Old 09-17-18, 05:46 AM
A
Member
Join Date: Jan 2013
Location: U.S.A.
Posts: 2,079
Received 67 Votes on 61 Posts
As long as you are comfortable doing the wiring, and are willing to spend a little more time on the front end to do it, my preference would be to eliminate the ballast as well. It's more likely than not that you will have ballasts fail anyway, so eliminate them and be done with it. I believe that they will be more energy efficient without the ballasts, and if a bulb ever does fail you will know it's exactly that, a failed bulb, and nothing else.
 
  #8  
Old 09-17-18, 07:33 PM
pcboss's Avatar
Forum Topic Moderator
Join Date: Jul 2002
Location: Maryland
Posts: 15,130
Received 78 Votes on 66 Posts
I was installing flat panel LED troffer replacements last week. Not sure is they were dimmable or not. Less than 2" thick at the driver compartment.
 
Reply
Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Trackbacks are Off
Pingbacks are Off
Refbacks are Off


Thread Tools
Search this Thread
 
Ask a Question
Question Title:
Description:
Your question will be posted in: