DoItYourself.com Community Forums > Cars, SUV's, Vans, Trucks, RV's, Boats and Gasoline Outdoor Power Equipment > Outdoor Gasoline and Electric Powered Equipment and Small Engines

Noma Performance Snowblower Need Manual

Thread Tools

Search this Thread

11-28-10, 10:31 PM

ask007

Member

Thread Starter

Join Date: Nov 2010

Location: canada

Posts: 1

Upvotes: 0

Received 0 Upvotes on 0 Posts

Noma Performance Snowblower Need Manual

Hi

I have noma performance snowblower Model 629104x31 purchased June 2000. This Noma is a powerful 29" dual-stage 10 HP blower.

I need Manual and parts list for Traini and Auger as well as original part number for 2 belts. Any idea where can I purchase OEM belts for this particular model ?

Anyone knows about please post it !

Thank you all

Upvote

11-29-10, 07:13 AM

Kev91

Member

Join Date: Nov 2010

Location: USA

Posts: 22

Upvotes: 0

Received 0 Upvotes on 0 Posts

ask007 Noma was bought out by Murray some years back and thus has become the Noma parts source. They use for the most part the same Noma part numbers. Try the link below it should take you to the manual needed as well as a possible parts source.

Murray st Parts Diagram Index for 629104X31

Upvote

Thread Tools

Search this Thread

Show Printable Version

Email this Page

Outdoor Gasoline and Electric Powered Equipment and Small Engines
craftsman snowblower 536.881851

D

dzsrfl on Nov 27, 2010

ref to problem from member dnewc1965, did you every get your fix? I have the same problem on my snowblower I just bought! thanks donRead More
Outdoor Gasoline and Electric Powered Equipment and Small Engines
20 year old Tecumseh 5hp rehabilitation

B

ben0712 on Nov 18, 2010

Hello, This is my first post regarding a 5hp Tecumseh engine, Model # H50-65499P. I found an old Garden Way chipper/shredder for sale for $150 at a garage sale a few weeks ago. The owner said he'd inherited it from a neighbor for whom he did some light handyman work, that it was from "about '85 or '90" and that it had been used about 4 hours over its lifetime. The engine started right up and we were able to send a stick through and shred it, so I bought it. I ran it for about a half hour on both the chipper and shredder openings and things worked fine. The engine required half choke to run, so I knew I probably needed to clean the carb out good. The belt was dry rotted. I replaced the spark plug and air filter, and I replaced the belt. I changed the oil (probably for the first time in its life) and the oil was dirty but no metal shavings evident. Now here's the problem. What I didn't realize was that the replacement belt I got was 29", and the spec was 29 1/4". With this size belt the clutch couldn't completely disengage. Proper operation requires the engine to get up to full throttle, then engage the clutch to turn the shredder assembly. Well, I didn't do that. I disengaged the clutch as far as I could, started it, and engaged the clutch before it got up to full speed. I was able to get it started, but it ran for about two minutes (turning the shredder) before the engine quit. At that point the pull-starter wouldn't budge. I removed the starter to get access to the flywheel nut. Turning the flywheel manually with the clutch disengaged, I could feel some resistance, so I inspected the belt and realized it was a quarter inch too short. I removed the belt and rotated the flywheel, and I can still feel some resistance at one specific point in the rotation. It feels like something is grinding inside the engine. I pulled the dipstick and discovered metal shavings in the oil. Now, my question is, where do I go from here? Have I wrecked this engine? What did I do exactly and what can I do to rehabilitate this fine old machine? I am not super-experienced with small engines but I'm a quick study, and I am willing to do a complete tear-down to learn more. Thanks!Read More

Ask a Question