DoItYourself.com Community Forums > Cars, SUV's, Vans, Trucks, RV's, Boats and Gasoline Outdoor Power Equipment > Outdoor Gasoline and Electric Powered Equipment and Small Engines

"White" SnoBlower-Missing Key

Thread Tools

Search this Thread

12-14-10, 12:09 PM

jjm106

Member

Thread Starter

Join Date: Dec 2010

Location: USA

Posts: 1

Upvotes: 0

Received 0 Upvotes on 0 Posts

"White" SnoBlower-Missing Key

I was just given a White 21" Electric Start Snow Blower. It's probably not more than 2 yrs old. The only and biggest problem is there is no ignition key. Can this problem be solved without trying to get a new key or is that the only answer?

Upvote

12-14-10, 12:37 PM

Gunguy45

Super Moderator

Join Date: Dec 2007

Location: USA

Posts: 19,281

Upvotes: 4

Received 6 Upvotes on 6 Posts

No Expert...but you could prob replace it for less than $20. Check with a local small engine repair place.

Upvote

12-14-10, 01:41 PM

indypower

Member

Join Date: Jul 2006

Location: Central New Hampshire

Posts: 658

Upvotes: 0

Received 0 Upvotes on 0 Posts

got a pic of the engine or at least where the key goes? If it is what I am thinking, the key is less than $5.

Upvote

Thread Tools

Search this Thread

Show Printable Version

Email this Page

Outdoor Gasoline and Electric Powered Equipment and Small Engines
Toro 421 Model 38010,TECUMSEH MODEL HS40-55513G

A

Arkman on Dec 13, 2010

Hi everyone, I'm new to the forum but so far I've found a lot of great info. Thanks everyone that contributes. I've gotten my snow blower fixed up a bit but I've got one more hurdle. But first let me give you some background info. This thing is older than I am and it sat for a while. Over the last 15 years its been used a handful of times and always started. I've actually had it for 3 seasons and I've had very little problems with it. Up until now just a leaky fuel line. I fixed that last season. This season I pulled it out of the shed and it started within 4 or 5 pulls. That was normal even on really cold days. The first snow it worked fine. The second snow it would die every so often, but if I primed it no problem it would fire right back up. I suspected an air leak of some kind. So I decided to tear it apart and clean up the carb (since it hasn't been for a long time). I did the carb service and fixed a leaking fuel hose which I suspect was the issue. Now when I prime I can feel the fuel being sucked in, before i could feel/hear it really just sucking air. I thought I was in the clear, then after I got it back together it won't start very well. Right now if I get the engine started it will stay running if I have it choked until is starts to choke itself out. This seems normal to me. The problem is when I take the choke off. The engine seems to rev up extremely high. I'm not really sure because I don't really have a good way to test the RPMs but they seem extremely high. I think I found someone on this forum say that the idle rpm should be 1700 and the high should be 3800. As it runs I'd guess that the idle is closer to 3000-4000. Now thats a total guess based on the sound of it and what I know of other small engines (not much). My initial thought was I just needed some carb adjustment but so far I'm not having any luck. Its a pain in the butt to start and when I get it started it either dies to fast to mess with the carb or the engine revs up high enough I feel the need to kill it...before it kills me. So far I've mainly tried adjusting the power screw. [URL="http://www.partstree.com/parts/?lc=toro_consumer&mn=38010,+421+Snowthrower,+1981+(SN+1000001-1999999)&dn=3311_642-1_642011-0007"]Its labeled as part 22 in this diagram.[/URL] I haven't adjusted the idle screw (#24 in the diagram) really but I could try that too I suppose. [B]The short version of this long story.[/B] It starts really hard and revs up way high without the choke. Does anyone have any ideas? I know with my boat motor carb there was suggested settings for the idle screw. Does anyone have any idea what that would be for this beast?Read More
Outdoor Gasoline and Electric Powered Equipment and Small Engines
Toro 824 belt replacement

S

SpeedBird67 on Dec 14, 2010

I'm replacing the stretched belts on my snowblower. I've got the new belts over both the auger pulley, and the drive pulley, however I don't seem to have enough slack to get them around the engine pulley. Any ideas? Do I need to un bolt the engine and "tip" it? Thanks!Read More

Ask a Question