Search: Posts Made By: shottys
Showing results 1 to 25 of 156
Search took 0.01 seconds.
Replies: 4
Views: 1,671
Posted By shottys

is it coming from the rear or front

is it coming from the rear or front
Replies: 4
Views: 1,267
Posted By shottys

The more and more you run your mouth the harder...

The more and more you run your mouth the harder and harder i will tear into you. if there is one thing i am good at is tearing down conceited people
Replies: 4
Views: 1,267
Posted By shottys

Sounds like you don't know much about these your...

Sounds like you don't know much about these your kinda right and kinda wrong. From the point of a person who reads published info your correct for the most part, but there is way way way more that...
Replies: 5
Views: 1,810
Posted By shottys

The site has nothing worth while to describe...

The site has nothing worth while to describe quality unless you care about how thick the metal is and size. What counts with an oil filter is whats the smallest particle it is filtering after say...
Replies: 6
Views: 1,604
Posted By shottys

He has a good point there if you are a person...

He has a good point there if you are a person with a medical condition and react to mold harshly. From a mechanical stand point it is fine, unless this troublesome molds grows to big that it clogs...
Replies: 9
Views: 1,324
Posted By shottys

I could see it improving power on a few engines...

I could see it improving power on a few engines because of induction system designs. But the throttle plate destroys the spinning air flow.
Replies: 4
Views: 1,267
Posted By shottys

corvette magnetic fluid dampers

I was talking with one of the engineers that helped designed this and didn't have much time to finish the conversation, i will see him next again tomorrow. But does anyone know if you completely...
Replies: 6
Views: 1,604
Posted By shottys

no it will not The compressor kicks on an...

no it will not

The compressor kicks on an off really hard when your driving. Turning the car off when the a/c is engaged is nothing compared to when it is working
Replies: 4
Views: 1,220
Posted By shottys

I already told him the pry bar thing before and...

I already told him the pry bar thing before and explained it very clearly. Your probably not prying in the right place or you are using a small pry bar. pry in between the tranny and the cv, turn a...
Replies: 1
Views: 1,127
Posted By shottys

i have a few ideas but i am not saying them with...

i have a few ideas but i am not saying them with seeing the schematics, if the thermostat doesn't help, a fan switch could be a possibility, also check for leaves and stuff blocking the radiator, i...
Replies: 8
Views: 1,695
Posted By shottys

The only way to get rid of it is to use strong...

The only way to get rid of it is to use strong disinfectants that won't take the color out of the carpet. soke the carpets hard and wet/dry vac them dry. you may need to do it a few times, most...
Replies: 3
Views: 1,166
Posted By shottys

look down a few threads for 94 chevy astro read...

look down a few threads for 94 chevy astro read that
Replies: 4
Views: 1,157
Posted By shottys

I am not familiar with that term for labeling a...

I am not familiar with that term for labeling a transmission, but a lot of things on cars are pulse width modulation and have been for years.

Is this technique used to measure shaft speeds in...
Replies: 8
Views: 1,373
Posted By shottys

i didn't say to replace them all only check for...

i didn't say to replace them all only check for bad ones if you are just buying the stuff by the foot its cheap and a good idea on stuff that old anyways
Replies: 15
Views: 8,902
Posted By shottys

schmuck You have a bad connection from the...

schmuck

You have a bad connection from the 12V line trace it down and find where the voltage drops to 6V.

unless you have a bad ground on the other multimeter lead
Replies: 4
Views: 1,952
Posted By shottys

don't recall seeing a zerk with no place to get...

don't recall seeing a zerk with no place to get socket on it, but it sounds like to me that the problem lies in the way you are greasing it you probably want to try different angles or different...
Replies: 2
Views: 1,587
Posted By shottys

first spray some penetrating oil in the latch and...

first spray some penetrating oil in the latch and all over it, then lift the hood about halfway up let it drop.


has the car been in an accident, did someone spin the rubber bumps out more, the...
Replies: 15
Views: 8,902
Posted By shottys

when you turn the knob to select a speed al your...

when you turn the knob to select a speed al your are doing is swithing in different valued resistors in series with the blower motor so that less voltage is at the motor, which causes it spin slower....
Replies: 5
Views: 1,810
Posted By shottys

every one says there's is the best, more media...

every one says there's is the best, more media isn't necessarily better thats a big advertising hype, change your oil and filter on a regular schedule and you don't need to worry about brand filter...
Replies: 2
Views: 1,164
Posted By shottys

probably is the the crankshaft seal, sorry i...

probably is the the crankshaft seal, sorry i can't see the leak to tell you where it is coming from. You will need a pulley puller to get to the seal and if you aren't able to do a timing belt then...
Replies: 15
Views: 8,902
Posted By shottys

9 times out of ten it is the blower resistor box ...

9 times out of ten it is the blower resistor box

could be switch or relay.

you need to use a multimeter and test for continuity
Replies: 7
Views: 1,706
Posted By shottys

6-8 years is not that uncommon, the battery in...

6-8 years is not that uncommon, the battery in my parents buick is 5 years old, and my buddies batteries are 7 years old. man did the years fly god i am getting old.

this is the chicago land...
Replies: 4
Views: 931
Posted By shottys

LIM stands for lower intake manifold

LIM stands for lower intake manifold
Replies: 3
Views: 1,317
Posted By shottys

he is talking about refrigerant recycling...

he is talking about refrigerant recycling equipment and a lot of shops do have it if you are from a larger city area, i am sure small shops in the middle of no where probably don't have it
Replies: 5
Views: 1,051
Posted By shottys

i may have miss lead here because something...

i may have miss lead here because something slipped my mind, if the screw holes have a notched out area so a bolts head can be recessed then they are holding the rotor on, other wise if there is no...
Showing results 1 to 25 of 156
 


 
Forum Jump