Search: Posts Made By: samahi72
Showing results 1 to 14 of 14
Search took 0.01 seconds.
Replies: 4
Views: 3,494
Posted By samahi72

Actually last night I scapped the paint off the...

Actually last night I scapped the paint off the tip and was surprised to see that the tip was a 4/15. The unit was recently rebuilt so now I am thinking of going to a 4/13 tip.

On a second note,...
Replies: 4
Views: 3,494
Posted By samahi72

Campbell Hausfeld Airless Spray Gun Info Needed.

I have a CH AL9415 3/4 hp .44 gpm airless sprayer. I need to get a new nozzle and tip for the gun. Typically all I paint is interior/exterior latex paint. My machine will not maintain pressure so...
04-29-08, 06:49 AM
Replies: 5
Views: 1,664
Posted By samahi72

Response 1. I didn't know that about the code....

Response 1. I didn't know that about the code. Presently, I can easily open the door to the circuit panel to access the circuit breakers, but can't remove the cover without removing the shelves. I...
04-29-08, 06:13 AM
Replies: 5
Views: 1,664
Posted By samahi72

Okay, here is the story and answer to your...

Okay, here is the story and answer to your questions. It is an attached garage. Due to some shelving, I could not get the circuit panel cover off without taking out the shelving to see what size...
04-28-08, 01:44 PM
Replies: 5
Views: 1,664
Posted By samahi72

Okay, I will check the romex. I am hesitant to...

Okay, I will check the romex. I am hesitant to change any circuit breakers to a larger size than what the electrician orginally installed. I just figured that the with everthing that was on that...
04-28-08, 12:11 PM
Replies: 5
Views: 1,664
Posted By samahi72

110 volts from a 220 service?????

I have a 220 service in my garage with a 50 amp breaker. My guess it is for a welder or air compressor. I have a small 110 volt welder that always trips the 15 amp breaker. Can I make a 110 volt...
Replies: 1
Views: 1,519
Posted By samahi72

110 volts from a 220 service?

I have a 220 service to my garage on a 50 amp service. I have a 110 volt mig welder that always trips the 15 amp service in the garage. Can I take a 220 cord and wire it to a 110 female plug? I...
04-09-08, 06:25 AM
Replies: 6
Views: 4,229
Posted By samahi72

Thanks I am a newby on this, while I think I have...

Thanks I am a newby on this, while I think I have a fundamental understanding of how they work, the terminology is confusing. What you said does make sense. Typically on the fan switch how much...
04-08-08, 12:45 PM
Replies: 6
Views: 4,229
Posted By samahi72

That it was to cold could very well be the...

That it was to cold could very well be the culprit. I stuck it on a rolling cart, took it outside early one morning, unhooked my natural gas bbq and hooked it up. I had a feeling that the fan was...
04-08-08, 08:18 AM
Replies: 6
Views: 4,229
Posted By samahi72

Furnace Limit Switch Fan

I have an old Janitrol overhead heater for the shop. I picked it up at an auction and I thought I would check it out and fix any problems before I install it. What I found it that the furnace will...
Replies: 4
Views: 11,333
Posted By samahi72

Tecumseh 6.5 Won't Prime.

I rebuilt the carb in my Scotts mower. The thing will not prime to start it. I give it a squirt of starter fluid and it starts right up and stays running. I believe I have cleaned and blown out...
03-12-08, 02:45 PM
Replies: 3
Views: 2,882
Posted By samahi72

Yes,it is that type of a heater. I was hoping...

Yes,it is that type of a heater. I was hoping the model number or serial number might give some clue.
03-12-08, 12:24 PM
Replies: 3
Views: 2,882
Posted By samahi72

Janitrol Overhead Heater Mounting Instructions

I just purchased an older Janitrol Overhead Heater, model number 68-070-8, Serial number 4667-4. Input is 70,000 BTU, Output=56,000 BTU. It has the standing pilot. I would like to find out...
10-05-06, 01:24 PM
Replies: 1
Views: 874
Posted By samahi72

Sounds like the exact same problem I had. To...

Sounds like the exact same problem I had. To repair mine, I replaced the solenoid/coil on top of the gas valve. You can see an exploded view of this on www.repairclinic.com. It was a very easy...
Showing results 1 to 14 of 14


 
Forum Jump