Search: Posts Made By: CAMINO KID
Showing results 1 to 25 of 200
Search took 0.01 seconds.
Replies: 9
Views: 1,468
Posted By CAMINO KID

you might try removing the choke blade and...

you might try removing the choke blade and reorienting the shaft and then reinsert the choke blade. I do not see the choke blade area to verify it.
Replies: 3
Views: 7,018
Posted By CAMINO KID

You probably had some gummy residue from the last...

You probably had some gummy residue from the last years fuel somewhere either at the needle valve or the float pivot causing the fuel to leak through the carb. After the present fuel you installed...
Replies: 106
Views: 109,540
Posted By CAMINO KID

Thanks for the addition as I could not find the...

Thanks for the addition as I could not find the site when I went to reply. I have been away from the shop for over four years now and still follow the site and help when I can. Thanks again.
Replies: 106
Views: 109,540
Posted By CAMINO KID

When I still had the shop after Troybilt went...

When I still had the shop after Troybilt went under, I used the 5/8 belts in the 29 1/4 length that you can get anywhere fan belts are sold. I used the heavy duty belts from Gates for years with no...
Replies: 73
Views: 83,292
Posted By CAMINO KID

make sure your nut is seated in the recess in the...

make sure your nut is seated in the recess in the height adjuster back side. the spacer has a shoulder that seats into the gear cover. you will have to hold the nut in place as you insert the bolt...
Replies: 15
Views: 18,124
Posted By CAMINO KID

You have to remove the belt pulley on the front...

You have to remove the belt pulley on the front housing and then you have the bearing retainer to take the nuts off and then the sides have some bearing retainers also to take the nuts and bolts off....
Replies: 73
Views: 83,292
Posted By CAMINO KID

The cable is adjustable on the side of the handle...

The cable is adjustable on the side of the handle bar. Loosen the nut on the cable holder and move it toward the deck and tighten. A little movement will do a lot. Make sure your belt is correct...
Replies: 73
Views: 83,292
Posted By CAMINO KID

The gear will have an R on one side of it and an...

The gear will have an R on one side of it and an L on the other side. The gears are the same but directional. If you can only see the R on a gear then put the R side inboard direction.
Replies: 73
Views: 83,292
Posted By CAMINO KID

All I can say is it takes some mussel to slid it...

All I can say is it takes some mussel to slid it off. It sounds as if you are trying to replace the upper plastic slide. Unhook every thing and then work the handle over the upper metal tubing...
Replies: 4
Views: 1,911
Posted By CAMINO KID

Take the gears off the axle shaft and look at the...

Take the gears off the axle shaft and look at the side of the gears. You will see an R or L. Put the gears on the axle shaft with the "R" facing out on the right side and the "L" facing out on the...
Replies: 73
Views: 83,292
Posted By CAMINO KID

Take the gears off the axle shaft and look at the...

Take the gears off the axle shaft and look at the side of the gears. You will see an R or L. Put them on the mower with the "R" facing out on the Right side of the mower and the "L" facing out on...
Replies: 2
Views: 2,331
Posted By CAMINO KID

Check safety switches.

This model has to have the brake on and some have to have the seat switch pressed by being seated. Also if the PTO is not showing that it is off you will not complete the circuit that allows the...
Replies: 106
Views: 109,540
Posted By CAMINO KID

Some of the earlier machines had centrifugal...

Some of the earlier machines had centrifugal clutches. Mine came with an idler and lever setup to tighten the belt to start the chipper after the engine has warmed up. Having serviced both types of...
Replies: 7
Views: 29,903
Posted By CAMINO KID

The spring has to apply an upward pressure to...

The spring has to apply an upward pressure to seat the needle valve in the carb. This was basically to smooth the flow of fuel to the carb due to machine vibration. The weight of the float should...
Replies: 2
Views: 929
Posted By CAMINO KID

If memory serves me right, since I nolong have...

If memory serves me right, since I nolong have any of the manuals, it goes towards the exhaust port.
Replies: 73
Views: 83,292
Posted By CAMINO KID

The transmission has a differential setup with...

The transmission has a differential setup with one wheel or the other being able to spin freely. The real way to test this is to lightly lift the mower up as you push on the handle and the wheels in...
Replies: 9
Views: 12,235
Posted By CAMINO KID

Toro has the stronger gear box on the auger. ...

Toro has the stronger gear box on the auger. After that Airens is the next best. Then you get into the brands made for everyone and their brother by MTD and American Yard Products (AYP). These...
Replies: 4
Views: 2,558
Posted By CAMINO KID

you might want to just look at a short block for...

you might want to just look at a short block for your unit if there is a cross over. There was a model in this area of time that had an old consumption problem that resulted in a relocation of the...
Replies: 10
Views: 69,240
Posted By CAMINO KID

We always adjusted the units in the shop under a...

We always adjusted the units in the shop under a 15 amp draw to run at 62 cycles or 3650 rpms. Your drop is within the tolerance the manufacturer gave us when I was still doing their warranty work...
Replies: 73
Views: 83,292
Posted By CAMINO KID

This model has a spring loaded key in the axle...

This model has a spring loaded key in the axle that slips when you push foward without the engine running. When you pull in reverse, the transmission must spin in reverse. Your transmission is not...
Replies: 2
Views: 1,555
Posted By CAMINO KID

I have sp2 pro and it did not see the drive. I...

I have sp2 pro and it did not see the drive. I loaded up an old ide drive and was able to see the SATA at that point. The manufacture did not have manual in the board box (Silicon Image) but...
Replies: 73
Views: 83,292
Posted By CAMINO KID

First you will need to remove the spark plug wire...

First you will need to remove the spark plug wire from the plug for safety. Next lift the mower up on edge with the air filter up. The smoke is you drive belt slipping on the transmission pulley. ...
Replies: 2
Views: 1,555
Posted By CAMINO KID

Upgrading dell 8250 to SATA drive

I have a Dell Demension 8250 where the ide drive failed. I am trying to install a SATA 500GB drive with drive card in the PCI slots. Everything that I try to make this unit see the SATA drive with...
Replies: 106
Views: 109,540
Posted By CAMINO KID

Tomahawk chipper

I have the hitch on my Tomahawk chipper, but do not think it will help you with your back. The chipper is quite heavy to tilt to use the hitch. I can send you pictures if you like and demensions so...
Replies: 13
Views: 8,517
Posted By CAMINO KID

If like you said all the bolts were tight, then...

If like you said all the bolts were tight, then make sure your breather or crankcase vent hose is not kinked off. Usually if you have excessive crankcase pressure, you will blow out a gasket at the...
Showing results 1 to 25 of 200
 


 
Forum Jump