Search: Posts Made By: LandToSea
Showing results 1 to 14 of 14
Search took 0.01 seconds.
06-16-07, 08:32 AM
Replies: 7
Views: 1,807
Posted By LandToSea

The linseed oil treatment worked out great so...

The linseed oil treatment worked out great so far. There were a couple spots I must have gone a little heavy on or not wiped off well enough which never cured and were tacky. I sanded them down (very...
04-21-07, 02:59 PM
Replies: 7
Views: 1,807
Posted By LandToSea

Thanks I will give it a shot! I was surprised...

Thanks I will give it a shot! I was surprised thta they did not have linseed oil at Home Depot?
04-19-07, 04:47 AM
Replies: 2
Views: 1,028
Posted By LandToSea

That's funny because when I caulked in the sinks...

That's funny because when I caulked in the sinks on the bamboo vanity tops that is exactly what I did. I had to mount the sinks and had not thought of sealing the cutout edges previously so I used...
04-19-07, 04:43 AM
Replies: 7
Views: 1,807
Posted By LandToSea

Do I brush or can I rag on the linseed oil? I...

Do I brush or can I rag on the linseed oil? I will apply a light coat once per week over the next few weeks. Will it be safe to work around the top after the initial treatment, meaning will the...
04-16-07, 05:23 AM
Replies: 4
Views: 5,427
Posted By LandToSea

Thanks for the reply! What is the best solvent to...

Thanks for the reply! What is the best solvent to use to remove the tape residue? I figured I was going to have to have different shade levels of the stain made for each wood type but have lost...
04-16-07, 05:16 AM
Replies: 7
Views: 1,807
Posted By LandToSea

Thanks for the suggestions! I could use the...

Thanks for the suggestions! I could use the beeswax finish since beeswax/mineral oil mix is more than likely what I will continue using on the kitchen island. My only concern is I do not want the...
04-15-07, 10:45 AM
Replies: 1
Views: 2,474
Posted By LandToSea

How to make curtains?

Are there any good websites that show how to make different types of curtains? Hemming a simple loop at the top I can do. but if I want to insert grommet rings etc. I need some help. Thanks!
04-15-07, 10:10 AM
Replies: 4
Views: 5,427
Posted By LandToSea

Matching stain on Mahogany doors with pine windows etc.

Hello all, me again! ;)
I have installed Mahogany exterior doors with mahogany returns and casing. I have also installed clear pine windows with pine returns and ash casing. I could not find clear...
04-15-07, 09:26 AM
Replies: 2
Views: 1,028
Posted By LandToSea

Walnut Kitchen Island top

I have installed a 2" thick Walnut butcher block top on my kitchen island. The craftsman treated the entire slab with beeswax/mineral oil finish since we will be using it for food prep and some...
04-15-07, 09:13 AM
Replies: 7
Views: 1,807
Posted By LandToSea

Bamboo vanity tops

I have installed new bamboo tops in my master bath and am trying to decide upon what finish to use. The tops are 1.5" thick cross multilaminated planks
I want to maintain the natural color,...
Replies: 7
Views: 45,724
Posted By LandToSea

Yes it was off. You have me thinking now that I...

Yes it was off. You have me thinking now that I might have tweaked a wire somewhere when puting everything back together. Then when I powered up it caused the short and may cause he new board to do...
Replies: 7
Views: 45,724
Posted By LandToSea

I went ahead and ordered the EC board since it...

I went ahead and ordered the EC board since it seems to be the problem no matter what. I was just hoping it was repairable. Any ideas as to what I could have done while installing the new top to have...
Replies: 7
Views: 45,724
Posted By LandToSea

Oh no!

I checked all the connections and they are tight. The cancel button is one of the buttons not currently functuning. How do these pad buttons work? The ones which are not working now do not seem as...
Replies: 7
Views: 45,724
Posted By LandToSea

Unhappy Error code F2 E1 on Kitchenaid?

I have a Kitchenaid Range model KERC507HBS3. I had broken the ceran top and installed a new one today. Since I had never done this before it did not go as smooth as it could have, but I got it...
Showing results 1 to 14 of 14


 
Forum Jump