Search: Posts Made By: SalR
Showing results 1 to 25 of 51
Search took 0.01 seconds.
Replies: 6
Views: 955
Posted By SalR

The water level is at the bottom of the heater...

The water level is at the bottom of the heater element so I figured it was correct. I didn't realize that it had a diverter so I will look into that further. Thanks for the info and link Manden.
Replies: 6
Views: 955
Posted By SalR

Yes, I do that every few months. I have never...

Yes, I do that every few months. I have never had much on the screen or in the filter
Replies: 6
Views: 955
Posted By SalR

Thanks for the reply PJmax...The model is...

Thanks for the reply PJmax...The model is wdf750sayw1 and I purchased it in 2012. Is the main wash pump the same as the circulator pump?
Replies: 6
Views: 955
Posted By SalR

Dishwasher arms not spinning

I have a Whirlpool Gold series dishwasher that has 3 arms. The bottom and middle are not spinning but the top one is. I've cleaned the arms and the sump area and filters with no results. I removed...
Replies: 2
Views: 975
Posted By SalR

Thanks for the reply Vic. I had a feeling that...

Thanks for the reply Vic. I had a feeling that would be the answer.
Replies: 2
Views: 975
Posted By SalR

Shower Cartridge Question

I have a Moen shower cartridge that works but can be tough to pull and push. Is there any way of lubricating the cartridge without removing it? I figure I could probably spray it with WD40 but did...
Replies: 2
Views: 2,800
Posted By SalR

Thanks for the reply Wirepuller38. Unfortunately...

Thanks for the reply Wirepuller38. Unfortunately I have done all that they mention already but it did not help. I even emailed canon but they said if I can't find paper in the printer then it...
Replies: 2
Views: 2,800
Posted By SalR

Canon MX700 all in one printer

I have had this printer for about 15 months and I currently have a paper jam error although I cannot find any paper in the printer. I have searched as best as i could and have blown canned air thru...
Replies: 1
Views: 1,277
Posted By SalR

Thermostat housing

Hi

I have a 97 Honda Accord SE 2.2 L 4 cylinder engine. A few weeks ago I had to replace the radiator because it was cracked. I did this and everything seemed fine until yesterday when I noticed...
Replies: 3
Views: 1,498
Posted By SalR

It looks to me like the toilet drains into the...

It looks to me like the toilet drains into the wall. I have 2 bathrooms and the toilets are back to back so I am guessing that they share the same drain and one bathroom has the drain in the floor...
Replies: 3
Views: 1,498
Posted By SalR

Bathroom Laminate Floor

I am planning to install a laminate floor in one of my bathrooms this week and when looking at the toilet I realized that the flange might be in the wall. If I remove the toilet and place it on top...
Replies: 1
Views: 863
Posted By SalR

Wall Flange...Maybe

I am planning to install a laminate floor in one of my bathrooms this week and when looking at the toilet I realized that the flange might be in the wall. The toilet has 2 bolts on the floor but the...
Replies: 5
Views: 1,486
Posted By SalR

Thanks Mitch. I got a small saw that looks more...

Thanks Mitch. I got a small saw that looks more like a gun and was able to get in there and get them off.

:)
Replies: 5
Views: 1,486
Posted By SalR

Removing Toilet bolts

Hi

I am removing my toilet to add a laminate floor and the closet bolts are frozen. I tried using a hacksaw to cut them off but am having trouble getting much blade on the bolts and it doesn't...
Replies: 22
Views: 2,193
Posted By SalR

Hvac...I saw the picture and the setup is quite a...

Hvac...I saw the picture and the setup is quite a bit different than what I have. I'm sure many improvements have been made over the years. I looked at my owners manual and found that my piping is...
Replies: 8
Views: 1,028
Posted By SalR

Well I took the car to the mechanic this morning...

Well I took the car to the mechanic this morning and he checked out the suspension and said all was good. He replaced the bad CV joint, I went back thru inspection and the car passed.

Thanks to...
Replies: 22
Views: 2,193
Posted By SalR

I ran the test as HVAC suggested and the pressure...

I ran the test as HVAC suggested and the pressure stayed steady. It has been warm here so the boilr hasen't cycled as much as normal but it seemded to go on and off enough to test. I looked at the...
Replies: 8
Views: 1,028
Posted By SalR

Thanks for all the advice guys. Your right about...

Thanks for all the advice guys. Your right about Christmas tow guy. This is no time to be paying for car repairs. Will have to just keep an eye on the other CV for now.
Replies: 8
Views: 1,028
Posted By SalR

Thanks for the quick response Mark. That was the...

Thanks for the quick response Mark. That was the answer I was hoping to hear.
Replies: 8
Views: 1,028
Posted By SalR

Suspension question

Hi

I have a 97 Honda Accord Coupe 4 cyl engine with 150K. It failed inspection in NJ because they said that the left front wheel has excessive side to side variation and suggested replacing the...
Replies: 22
Views: 2,193
Posted By SalR

Hi guys I posted more pics ...

Hi guys

I posted more pics
http://i132.photobucket.com/albums/q18/srappajr/boiler2pics001.jpg
http://i132.photobucket.com/albums/q18/srappajr/boiler2pics002.jpg...
Replies: 22
Views: 2,193
Posted By SalR

I have posted some pics ...

I have posted some pics
http://i132.photobucket.com/albums/q18/srappajr/boilerpics001.jpg
http://i132.photobucket.com/albums/q18/srappajr/boilerpics002.jpg...
Replies: 22
Views: 2,193
Posted By SalR

I replaced the tank but unfortunately there was...

I replaced the tank but unfortunately there was no place to put a valve. I bled the system and pressured to 15psi. The pressure seems to be doing good. It rises when the boiler is firing but drops...
Replies: 22
Views: 2,193
Posted By SalR

Thanks NJ Trooper...and yes it could be ....I...

Thanks NJ Trooper...and yes it could be ....I live in Howell NJ.

Last night I had reduced the pressure to around 15 and shut the water inlet valve off and this morning after the heat had run...
Replies: 22
Views: 2,193
Posted By SalR

Thanks for the response Grady. So if I...

Thanks for the response Grady.

So if I reduce the boiler pressure to zero and the tank pressure is around 12 then the culprit is probably thr reducing valve. But if the tank pressure also drops...
Showing results 1 to 25 of 51
 


 
Forum Jump