Search: Posts Made By: ryano
Showing results 1 to 13 of 13
Search took 0.01 seconds.
Replies: 5
Views: 19,628
Posted By ryano

check this

heya,
FIrst, check if the fuel line has a filter at the end of it in the tank..change it if present.

Then make sure the spark plug is clean.

Make sure when you start it you are fully engaging...
Replies: 14
Views: 8,333
Posted By ryano

greg, I appreciate your help so much and I agree...

greg, I appreciate your help so much and I agree at this point completely about further testing on the motor. I don't own a clamp on meter, so my question is what are the advantages to owning this...
Replies: 14
Views: 8,333
Posted By ryano

$100 for the answer

OkI am ready to give up money for the answer here!!

I replaced the check valve and took the head off and all seals are good and all flappers seem to be just fine and operating as they should.

I...
Replies: 14
Views: 8,333
Posted By ryano

yes

yeah I hear ya. that is where I was going with all this b/c the motor seems to operate fine even under load so Ithink it is mechanical. I just bought a check valve and will have it in a week...
Replies: 14
Views: 8,333
Posted By ryano

flaps seem to suck air in

heya, without disassembly of the heads the small flapping valves were taking in air when it was just starting up and trying to build up to the initial 30 psi. Can pressure in the tank of 30 psi...
Replies: 14
Views: 8,333
Posted By ryano

Help my basement awaits..Check valve lookin good but not so good?

Hey, I am in the middle of finishing my basement and I lost my other compressor so it is buy a new one or resurrect this one.

I was going over this thing again for another 1/2 hr today and it just...
Replies: 14
Views: 8,333
Posted By ryano

This seems mechanical

No extension cords in use and it does the same thing no matter 15 or 20 amp breaker. Well, my theory here is that the motor runs fine without any mechanical restrictions like pressure in the tank or...
Replies: 14
Views: 8,333
Posted By ryano

Air Compressor has backpressure?!?!?

First time posting....I have read through any other threads that looked like this and didn;t quite find the answer...

I have a 15 gal or so horizontal 3 hp Sears compressor (mod.919.176830) and...
Replies: 2
Views: 1,420
Posted By ryano

how to locate

well, thank you for a response. I actually did what you suggested almost immeditely and found that teh short is in teh welding machine somewhere. My question is I guess how would you go about going...
Replies: 2
Views: 1,420
Posted By ryano

Welder immediatly trips circuit problem

Hey,
I have anESAB mini arc 130 110v welder and it has been fine since the 90's but just recently I went to turn it on and it trips the circuit immediatley. I took the cover off of it and nothing...
09-29-08, 07:46 PM
Replies: 5
Views: 7,137
Posted By ryano

yes this motor can be wired for 220 or 110. is...

yes this motor can be wired for 220 or 110. is there any good info out there on what a normal motor should look like on the inside and how to test individual components?

Thank you for all the...
09-28-08, 07:41 PM
Replies: 5
Views: 7,137
Posted By ryano

thanks for the reply. Is there any good info out...

thanks for the reply. Is there any good info out there on the net that has the exact process of doing this stuff with home tools like a multimeter?

Lets look at one of the problems: I put a...
09-28-08, 10:20 AM
Replies: 5
Views: 7,137
Posted By ryano

Electric motor testing-is it good or not?

Hello all,
First time posting. I have about three old machines (welding and air compressor) and I hate to throw them out without knowing for sure if they are bad. I have what seems to be issues...
Showing results 1 to 13 of 13


 
Forum Jump