Search: Posts Made By: JerryCaldwell
Showing results 1 to 25 of 41
Search took 0.01 seconds.
Replies: 1
Views: 197
Posted By JerryCaldwell

Kenmore washing machine bounces around loudly during spin cycle

Our Washer goes whahunka-wahunka-wahunka and bounces around loudly during the spin cycle even with average-sized load. This is a recent development, it has worked well until recently even with heavy...
04-23-19, 07:28 PM
Replies: 3
Views: 418
Posted By JerryCaldwell

So if I understand correctly I should check for...

So if I understand correctly I should check for continuity between ground and load neutral? In this case flex conduit it ground path.
04-23-19, 06:19 PM
Replies: 3
Views: 418
Posted By JerryCaldwell

GFCI mystery

I am installing new GFI outlets in kitchens of apartment building. When I connect line hot and neutral the GFI will Reset and Test with no apparent problems. When I connect the load hot and neutral...
Replies: 2
Views: 878
Posted By JerryCaldwell

Rotten eggs smell from dishwasher

Model: ffbd2408nw1a. Frigidaire dishwasher

I cleaned strainers and rotor, still smells when run.
Please advise us. *Big Grin*
Replies: 2
Views: 512
Posted By JerryCaldwell

No Icemaker, so it must be condensate drain as...

No Icemaker, so it must be condensate drain as you suggest. I was wondering if it might be common problem with this particular model.
Replies: 2
Views: 512
Posted By JerryCaldwell

Smile Refrigerator dripping water inside near back

Near new refrigerator in a rental is dripping water into refrigerator section about 6 " from the very back in center of fridge. Everything seems to be working OK, freezer section is froze and lower...
Replies: 3
Views: 4,324
Posted By JerryCaldwell

Water drips intermittently from housing for light...

Water drips intermittently from housing for light bulb.
Replies: 3
Views: 4,324
Posted By JerryCaldwell

New Frigidaire refrigerator dripping water inside -

I replaced fridge a short time ago and it has been dripping water ever since. About 1 small bowl of water every 4-5 days.

Vendor sent tech who clearly had no clue; tinkered with it a few times and...
Replies: 19
Views: 1,440
Posted By JerryCaldwell

Got 'er done!

After much procastination I moved ahead with my idea to cut the steel sink out rather than disrupt the tile counter-top. I made the long cuts as much possible with my old Milwaukee worm drive and...
Replies: 19
Views: 1,440
Posted By JerryCaldwell

Proceeding with grinder

Thank you to all for the advice and encouragement. I'm off to get a new grinder with vacuum attachment and some cutting wheels.:dogrun:
Replies: 19
Views: 1,440
Posted By JerryCaldwell

Thanks so much for your input. Near as I can...

Thanks so much for your input. Near as I can tell the outer dimensions of the sink are 21 x 18 1/4. I can see underneath that, as you said the flange of the sink sits on top of 1x rough top and the...
Replies: 19
Views: 1,440
Posted By JerryCaldwell

Hello Norm201 There are no undermount clips....

Hello Norm201
There are no undermount clips. The flange of the sink is underneath the tile and on top of the rough top.

Thank you!
Replies: 19
Views: 1,440
Posted By JerryCaldwell

The flange of the sink extends underneath the...

The flange of the sink extends underneath the tile. It is not caulked in unfortunately.
Replies: 19
Views: 1,440
Posted By JerryCaldwell

I have found a drop-in sink that will fit in the...

I have found a drop-in sink that will fit in the cutout and leave roughly 1/2' around the edge to set in a fat bead of silicone. Dimensions inside the bullnose are 19 1/4 wide x 16 3/4 deep;
Replies: 19
Views: 1,440
Posted By JerryCaldwell

Advice on replacing steel sink without disturbing tile.

I need to replace a steel sink. It looks new on top but the overflow channel underneath is rusted out and leaking. I was thinking I could just cut off the flange around perimeter, leave the tile in...
Replies: 2
Views: 862
Posted By JerryCaldwell

Frigidaire Dishwasher - leak possibly from door

I have a Frigidaire Professional ( Model #FPHD2481KF1) that leaks occasionally. I have checked the pump and all the hoses, under the machine and they all appear dry. I run it through a cycle and it...
Replies: 13
Views: 5,166
Posted By JerryCaldwell

Door closer dilemma

Hello Door Doctor and rstripe

I think I'll go with replacing it with the Norton 1600.

Any thoughts on how I might further ensure the door operates quietly?


I greatly appreciate your...
Replies: 13
Views: 5,166
Posted By JerryCaldwell

The UL label says R25111 Ul Listed 47V5 ...

The UL label says
R25111
Ul Listed 47V5

Thank you! !

DOORDOCTOR;2297789]arm preload angle (when you put arm on shaft) has alot to do withhow much preload is on the arm, if your closer has...
Replies: 13
Views: 5,166
Posted By JerryCaldwell

Hello DOORDOCTOR and rstripe The closer is...

Hello DOORDOCTOR and rstripe
The closer is preloaded. Perhaps I'll load it a bit more on the replacement to get the door to latch.
I think I'll inquire where I bought it and get a better quality...
Replies: 13
Views: 5,166
Posted By JerryCaldwell

Cool Here's a couple photos. The arm is disconnected...

Here's a couple photos. The arm is disconnected to avoid having door slam. It worked OK for a couple years but lately it will close very slowly one cycle and slam shut the next. It has never seemed...
Replies: 13
Views: 5,166
Posted By JerryCaldwell

Quiet door closer replacement for apartment entrance

I am getting complaints from tenants adjacent to the front door that it frequently slams shut. The closer does not work consistently when adjusted to close slowly and quietly so I have decided to...
Replies: 3
Views: 751
Posted By JerryCaldwell

Correction: Model is FRT18B4AW4

I pulled off back panel in freezer. There is light frost on evaporator coil and the fan seems to work fine.

It does not seem to get colder when setting in lower section is changed.
Replies: 3
Views: 751
Posted By JerryCaldwell

Freezer OK, lower part not cold

Electrolux Home Products
Model: FRT1884AW4
S/N: BA20306759

This unit recently started not cooling the lower refrigerator section. The freezer seems OK.

Also can you tell me how old this...
10-02-13, 01:23 PM
Replies: 1
Views: 1,193
Posted By JerryCaldwell

OK, I got a replacement part, twisted out the old...

OK, I got a replacement part, twisted out the old burner, disconnected and reconnected the ignitor wires and now none of the ignitors work?!? Any suggestions?

They all worked except for the one I...
10-02-13, 08:07 AM
Replies: 1
Views: 1,193
Posted By JerryCaldwell

How to replace gas burner on Magic Chef stove

I have a need to replace front right burner on Magic Chef Stove (Model #CGR1420BDM).

It is corroded on one side so that the gas comes through unevenly and the igniter is broken off.

I think I...
Showing results 1 to 25 of 41
 


 
Forum Jump