Search: Posts Made By: PJmax
Showing results 1 to 25 of 200
Search took 0.01 seconds.
Yesterday, 09:33 PM
Replies: 1
Views: 29
Posted By PJmax

I don't have any first hand knowledge and as far...

I don't have any first hand knowledge and as far as I know.... none of our staff has either.
Staff and members will stop by.

I was checking around and located this supply company. Could be...
Replies: 5
Views: 137
Posted By PJmax

The temperature sensor would snap into the H/C...

The temperature sensor would snap into the H/C mixing box and plug into J9.
J9 is the white plug (red, blue, white wires) in the bottom right of the picture.
There is no sensor or wiring.

That...
Replies: 1
Views: 17
Posted By PJmax

That idler pulley is shot. It's got a hole in it....

That idler pulley is shot. It's got a hole in it.
Typically the assembly is replaced.

DC97-07509B idler pulley
DC93-00634A idler pulley assy.
Idler pulley assy...
Yesterday, 08:34 PM
Replies: 10
Views: 152
Posted By PJmax

You didn't mention your wiring was in conduit. ...

You didn't mention your wiring was in conduit.
That box got wet. Those wires are corroded.
The blacks and red splice is just as bad.

You should have enough wire to redo those splices.
Once...
Replies: 9
Views: 2,389
Posted By PJmax

It's the fingerprint resistant coating that is...

It's the fingerprint resistant coating that is peeling. Unfortunately I don't see any manufactures standing behind the finish. Samsung has a class action suite for it's failed coatings.


What is...
Yesterday, 06:40 PM
Replies: 10
Views: 152
Posted By PJmax

Usually when I get a call like that the customer...

Usually when I get a call like that the customer has no idea of everything on the circuit.
So the customer pays me to locate everything on the circuit.

I create a diagram in my head that matches...
Replies: 5
Views: 103
Posted By PJmax

Unfortunately it's not east to offer help on a...

Unfortunately it's not east to offer help on a project like that without actually seeing it.
I would try to get a plumber there to at least look at the job.
Do get prices from several plumbers.
Replies: 2
Views: 42
Posted By PJmax

Those use a 350LM cob chip and the specs for that...

Those use a 350LM cob chip and the specs for that part shows 5 watts @ 12-14vdc/vac
Yesterday, 06:13 PM
Replies: 2
Views: 53
Posted By PJmax

Welcome to the forums. That is a 200A...

Welcome to the forums.

That is a 200A service with a 200A main breaker so technically the wiring to your home and garage panel is protected at 200A.

Technically you could connect two panels...
Replies: 3
Views: 34
Posted By PJmax

If you need detailed help... post the model...

If you need detailed help... post the model number.
Yesterday, 06:02 PM
Replies: 5
Views: 156
Posted By PJmax

Awesome. Good job. Thanks for letting us know how...

Awesome. Good job. Thanks for letting us know how you made out.
Yesterday, 05:58 PM
Replies: 10
Views: 152
Posted By PJmax

You have normal voltage as measured from hot to...

You have normal voltage as measured from hot to ground.
You have low voltage as measured from hot to neutral.
You do have a neutral problem.

As you plug a load in..... the voltage will go down...
Yesterday, 05:33 PM
Replies: 5
Views: 111
Posted By PJmax

I confess..... now I'm completely lost....

I confess..... now I'm completely lost. :confused:

I left you the parts breakdown pdf previously.
It clearly illustrates the direction of the diffuser.
The open side of the diffuser faces the...
Yesterday, 05:05 PM
Replies: 2
Views: 30
Posted By PJmax

You have three cables...... that's 3 white, 3...

You have three cables...... that's 3 white, 3 black and 3 ground wires.
Keep the 3 white wires connected and add the white from the WiFi switch (AC-N) to that splice.
You will need a short piece of...
Yesterday, 04:46 PM
Replies: 13
Views: 150
Posted By PJmax

You had a bunch of pics that weren't needed. I...

You had a bunch of pics that weren't needed. I deleted them.
I kept and labeled the one that shows what I needed on the defrost board.

The ID plate has a lot of information on it.
It's either...
Yesterday, 04:34 PM
Replies: 5
Views: 28,104
Posted By PJmax

The motor reference ID number is damaged. If...

The motor reference ID number is damaged.
If you are going to use on 120v..... try the diagram I left.

After you confirm the motor ok... we can move onto switching/pedals.
Yesterday, 04:20 PM
Replies: 5
Views: 56
Posted By PJmax

The moral of the story is be very wary and take...

The moral of the story is be very wary and take AI with a big grain of salt.
Replies: 3
Views: 42
Posted By PJmax

I'm old school..... I still use a siphon. I...

I'm old school..... I still use a siphon.
I love the taste of high test in the morning.
...
Yesterday, 04:10 PM
Replies: 5
Views: 91
Posted By PJmax

The code requirement for a neutral in every...

The code requirement for a neutral in every switch box is on new work.
Old work is grandfathered in.
Replies: 6
Views: 95
Posted By PJmax

That is the correct valve. That would leave a...

That is the correct valve.
That would leave a possible problem with the fill tube heater.

Full service manuals are not free and are not posted.
Send me a PM with your email address and I'll send...
Replies: 5
Views: 103
Posted By PJmax

You cannot install a floor drain without opening...

You cannot install a floor drain without opening the floor or ceiling below.
Replies: 15
Views: 649
Posted By PJmax

Welcome to the forums. There is definitely a...

Welcome to the forums.

There is definitely a stop when adjusting inwards.
Not sure if the adjustment piece can unscrew out. I'd doubt it.
Replies: 1
Views: 39
Posted By PJmax

Ejection pit..... basement ? You can extend...

Ejection pit..... basement ?

You can extend the vent.
You're showing a shower there now.
Is that moving ?
03-16-24, 10:05 PM
Replies: 8
Views: 212
Posted By PJmax

Good job. Took a while but you got there. ...

Good job. Took a while but you got there. :thumbup:
Replies: 2
Views: 78
Posted By PJmax

It's the luck of the draw. You could get a good...

It's the luck of the draw. You could get a good aftermarket part or..... not.

I was looking at replacements and there are dozens and they all use the same exact picture. :confused:
Does that mean...
Showing results 1 to 25 of 200
 


 
Forum Jump