Search: Posts Made By: Geochurchi
Showing results 1 to 25 of 200
Search took 0.02 seconds.
03-17-24, 04:18 AM
Replies: 3
Views: 129
Posted By Geochurchi

Thanks Pete. I found it on the floor under our...

Thanks Pete. I found it on the floor under our bench in our engine shop, while I was looking for the NUT that is lost from the fixture in my other post, the porcelain socket got broken and I was...
03-16-24, 02:36 PM
Replies: 3
Views: 129
Posted By Geochurchi

What is this?

What is this?
https://cimg5.ibsrv.net/gimg/www.doityourselft.com-vbulletin/2000x1504/img_4283_661a82cf5316ef3ab083f9063d882f917f90f40e.jpeg...
Replies: 1
Views: 58
Posted By Geochurchi

Industrial barn fixture

Hi All , anyone know where I would be able to locate this fixture part, I have searched multiple sites and can’t find anything like it.
Thanks
Geo🇺🇸...
Replies: 8
Views: 215
Posted By Geochurchi

Got it, I thought it was strange to have two...

Got it, I thought it was strange to have two thermal couples, hence my question.
Thanks
Geo🇺🇸
Replies: 8
Views: 215
Posted By Geochurchi

Just curious, why the second thermal couple, was...

Just curious, why the second thermal couple, was that factory installed?
Geo🇺🇸
03-10-24, 07:57 AM
Replies: 10
Views: 241
Posted By Geochurchi

It appears to be an under voltage when the light...

It appears to be an under voltage when the light dims or the fan slows down, are they both on the same circuit breaker, what else is on that circuit?
Geo🇺🇸
Replies: 4
Views: 112
Posted By Geochurchi

I think the plan will be to install plastic...

I think the plan will be to install plastic anchors and use hex head screws with washers, based on the fact that hopefully the banner will remain in place for 4 months then it will be removed, I...
Replies: 4
Views: 112
Posted By Geochurchi

Probably could use plastic anchors, we were...

Probably could use plastic anchors, we were looking for something that could be easily removed , possible using a thumb screw.
Geo🇺🇸
Replies: 4
Views: 112
Posted By Geochurchi

Cement block anchors

Good morning, looking for thoughts as to which anchor is best for cement blocks, plan is to install anchors (1/4 /20,) then install thumb screws to hold a banner which would be removable.
Thanks ...
03-03-24, 02:53 PM
Replies: 9
Views: 308
Posted By Geochurchi

I would keep bugging them and make it sound like...

I would keep bugging them and make it sound like it is much worst than it is, they are a PIA to deal with.
Geo🇺🇸
03-02-24, 02:45 PM
Replies: 2
Views: 144
Posted By Geochurchi

Make the splices inside the motor enclosure. ...

Make the splices inside the motor enclosure.
Geo🇺🇸
02-29-24, 05:54 PM
Replies: 5
Views: 184
Posted By Geochurchi

Hi, where was the wire you capped connected?, how...

Hi, where was the wire you capped connected?, how many conductors do you have on the receptacle?
Geo🇺🇸
02-29-24, 04:42 PM
Replies: 2
Views: 88
Posted By Geochurchi

1 1/2 hp pump

HI All, we have a 1 1/2 HP submersible pump, 240 volt, single phase, is a motor controller required, seems like a Size 0 , or can the pump be protected by appropriate fusing or CB.
Thanks
Geo🇺🇸
02-29-24, 10:02 AM
Replies: 3
Views: 137
Posted By Geochurchi

Air flow

Hi , do you have good air flow when you are in Heat or Cooling modes? post a pic of the motor name plate
Replies: 2
Views: 60
Posted By Geochurchi

That’s the one! What is the 29” seems like a...

That’s the one! What is the 29” seems like a piece of threaded rod would be needed, I can’t understand why this should be so hard find.
Thanks
Geo🇺🇸
Replies: 2
Views: 60
Posted By Geochurchi

MA022 LM Bolts

Good morning, anyone know the specs on these bolts , ie length, I believe they are 5/16 X 18 threads and they use a nylon nut, which way is the bolt head supposed to be located, through the bracket...
Replies: 1
Views: 135
Posted By Geochurchi

Black algae

Good morning. Looking for opinions on how best to deal with these black streaks, 5 buildings are involved in SW Florida , lite color shingles, roofs are approximately 6 years old
Thanks for your...
Replies: 8
Views: 10,304
Posted By Geochurchi

Manual

Check this manual out if you don’t have one. Post a pic of the wire location, if one wire goes to the ignition switch, it won’t hurt to connect the other to ground, I suspect that if the engine...
02-11-24, 06:33 AM
Replies: 9
Views: 201
Posted By Geochurchi

Hi, are you sure it is a model 500M? Geo🇺🇸

Hi, are you sure it is a model 500M?
Geo🇺🇸
Replies: 1
Views: 152
Posted By Geochurchi

Shower replacement

Hi All, thinking of possibly removing a fiberglass tub and shower enclosure and replacing with full tile , floors and walls, my main concern would be the tile floor. getting the right pitch so that...
Replies: 3
Views: 265
Posted By Geochurchi

Just curious, what do you plan on doing with...

Just curious, what do you plan on doing with these once they are rebuilt? I suspect you could buy new for the price of the parts.
Geo🇺🇸
Replies: 1
Views: 115
Posted By Geochurchi

B&S Vangard

Good morning, any danger running a motor with no exhaust manifold attached for a short period of time?
Thanks
Geo🇺🇸
12-14-23, 04:25 PM
Replies: 9
Views: 393
Posted By Geochurchi

Got it Pete, Water source heat pump, we had...

Got it Pete, Water source heat pump, we had buildings with 100’s these small units above the ceiling, years ago tho.
Geo🇺🇸
Replies: 6
Views: 285
Posted By Geochurchi

Thanks , all set, I like the idea with the dowel....

Thanks , all set, I like the idea with the dowel.
Geo🇺🇸
12-14-23, 05:43 AM
Replies: 9
Views: 393
Posted By Geochurchi

Hi, that unit appears to be a chilled water...

Hi, that unit appears to be a chilled water system, no compressor there, on a call for cooling the chilled water valve would open allowing chilled water to flow through the coil, is the valve opening...
Showing results 1 to 25 of 200
 


 
Forum Jump