Search: Posts Made By: tbone8
Showing results 1 to 18 of 18
Search took 0.01 seconds.
03-18-17, 01:49 PM
Replies: 9
Views: 3,827
Posted By tbone8

Don't know if this will help, but here is a pic...

Don't know if this will help, but here is a pic of the breakers in question and how they were labeled. #3 is the hot-neutral reversed and #5 is the bathroom, I think.

78448

78449
03-17-17, 09:51 PM
Replies: 9
Views: 3,827
Posted By tbone8

The breakers are all single ones, no red wires....

The breakers are all single ones, no red wires. There are a couple 220 breakers but they are fine. The breakers are next to each other, not the dual one like you posted. My bad, I mistook the...
03-17-17, 08:42 PM
Replies: 9
Views: 3,827
Posted By tbone8

Yes, the circuits are one on top of the other....

Yes, the circuits are one on top of the other. Wires going to the breaker are black wires.
03-17-17, 05:35 PM
Replies: 9
Views: 3,827
Posted By tbone8

Ok, been painting the past few weeks and finally...

Ok, been painting the past few weeks and finally got around to messing with this. The hot-neutral issue I will figure out later, its the dead bathroom outlets that have me baffled. I will detail this...
03-07-17, 02:05 PM
Replies: 9
Views: 3,827
Posted By tbone8

Receptacles: open hot, hot-neutral switched

I built my house, did all the wiring myself so I have some knowledge of electrical wiring. On my old house that I am getting ready to sell is the problem. When I bought it 25 years ago, the...
Replies: 8
Views: 1,291
Posted By tbone8

When I try to enter the new MC, it doesn't give...

When I try to enter the new MC, it doesn't give me the confirmation beep at the end. I don't recall if the keys beep when pressed, I think so. I have a second keypad, a 6152 I believe, I am gonna try...
Replies: 8
Views: 1,291
Posted By tbone8

Yessir, I can do everything it just wont let me...

Yessir, I can do everything it just wont let me change the master code. I was able to change the installer code with no problem. This newer pad seems to have quirks, supposed to be more user friendly...
Replies: 8
Views: 1,291
Posted By tbone8

Tried that too, didn't work.

Tried that too, didn't work.
Replies: 8
Views: 1,291
Posted By tbone8

Oops, sorry, a Vista 20p.

Oops, sorry, a Vista 20p.
Replies: 8
Views: 1,291
Posted By tbone8

How to change master code with 6162 keypad

Howdy, probably an extremely dumb question, but I can't seem to figure out how to change master code with 6162 keypad. Master code + [8] + 02 + new user’s code + new user’s code wont work on the...
10-23-14, 04:21 PM
Replies: 5
Views: 1,176
Posted By tbone8

Could you tell me who manufactures the greensand...

Could you tell me who manufactures the greensand plus systems?
10-22-14, 09:18 PM
Replies: 5
Views: 1,176
Posted By tbone8

What do you think of a greensand system with a...

What do you think of a greensand system with a chlorine injector? This what I am leaning towards.
10-21-14, 04:49 PM
Replies: 5
Views: 1,176
Posted By tbone8

Ideas for well water treatment

I am building a new house, had the well put in and water tested:
Calcium:109.8 mg/L
Iron 1.060 mg/L
Magnesium 43.54 mg/L
Alkalinity 350 mg/L
Hardness 450 MG/L
pH 6.9
Total Dissolved Solids...
06-01-14, 10:46 PM
Replies: 6
Views: 19,529
Posted By tbone8

I found the copy of the truss design. Reading...

I found the copy of the truss design. Reading here, what about a layer of rigid foam at the top (blue line) and mesh on the bottom to blow it in, then drywall? The 4' outside is a porch overhang.
06-01-14, 08:41 AM
Replies: 6
Views: 19,529
Posted By tbone8

Advice on insulating a scissor truss ceiling

I am building a house on property where I grew up in Northern Indiana. I have one room that is 36' wide by 24'. Attached is a basic pic of the truss design. The pitch of the ceiling is 3:12 and I...
Replies: 8
Views: 1,396
Posted By tbone8

Yes, I understand the logic behind the mortar...

Yes, I understand the logic behind the mortar bed. The question would be how to do so. The thing is one piece and weighs 200lbs. There would be no real way to place the thing on the bed. It would...
Replies: 8
Views: 1,396
Posted By tbone8

From the instructions: Be sure the bottom of...

From the instructions:

Be sure the bottom of the module is firmly supported against the floor. You may need to adjust some of the
framing. Use shims as necessary. However, no additional support...
Replies: 8
Views: 1,396
Posted By tbone8

Installing a kohler sonata shower

Hi, first post here but been a reader for a long time. Anyways, I am building a new home a got a Kohler Sonata 60" 1 piece shower. When it is in place, there is a gap of about 1" under the shower...
Showing results 1 to 18 of 18


 
Forum Jump