Search: Posts Made By: gstullo
Showing results 1 to 20 of 20
Search took 0.01 seconds.
02-16-14, 11:38 AM
Replies: 35
Views: 10,112
Posted By gstullo

I added the wire and now the emergency heat works...

I added the wire and now the emergency heat works properly. It also seemed to fix the cold air during defrost mode too.

Thanks for all the help. The system is now up and running really well!
01-09-14, 12:53 AM
Replies: 35
Views: 10,112
Posted By gstullo

So to do this I should just add a short wire...

So to do this I should just add a short wire between the wire wires and the black where they enter/exit the handler?
01-08-14, 06:12 PM
Replies: 35
Views: 10,112
Posted By gstullo

No jumper between aux and e in Stat or between...

No jumper between aux and e in Stat or between white and black wires in the handler.

Would jumping any of these together cause the HP to turn off even when just an Aux call comes from the Stat?
01-08-14, 05:57 PM
Replies: 35
Views: 10,112
Posted By gstullo

I went ahead and replaced both the parts for each...

I went ahead and replaced both the parts for each coil. Even though it was probably just bad relays and not the rectifiers, I replaced those too as they were so inexpensive.

Good news is that the...
01-01-14, 10:30 AM
Replies: 35
Views: 10,112
Posted By gstullo

Happy New Year! Sorry for taking so long to...

Happy New Year!

Sorry for taking so long to reply...

The parts are:

1) Warren Tech CCR9-5
2) ORG T9CPID52-22 N.O. 30A. 240VAC. 02371

Should I replace both parts?
12-17-13, 08:52 AM
Replies: 5
Views: 2,230
Posted By gstullo

Sillcock with odd connection

Good morning everyone,

I've got a sillcock that is leaking like crazy. This started as a really slow drip and is now a steady stream. Trouble is that this house still has polybutylene piping which...
12-12-13, 05:05 PM
Replies: 35
Views: 10,112
Posted By gstullo

I just had that power off to everything and...

I just had that power off to everything and pulled the connections to the coils at A and B. I got around 11 ohms at each point so I assume that the coils are good?

G and H also get around 1 ohm....
12-11-13, 04:50 AM
Replies: 35
Views: 10,112
Posted By gstullo

If there are two heat strips, does it mean that...

If there are two heat strips, does it mean that one is active in AUX mode and both in Emergency?

Before i look into replacing the relays, should i go ahead and remove the thermostat and tie the R,...
12-10-13, 09:05 AM
Replies: 35
Views: 10,112
Posted By gstullo

So a dead short means ohms of 0 or nearly 0? And...

So a dead short means ohms of 0 or nearly 0? And this is good?

Should the relays both be on in EM heat and/or aux heat?

Yesterday I noticed no voltage to these in either case. I did brush up...
12-10-13, 05:44 AM
Replies: 35
Views: 10,112
Posted By gstullo

So what are the relays and how do I replace them?...

So what are the relays and how do I replace them?

Is there any way to, or should I, check that the heat strips are good?
12-09-13, 11:02 AM
Replies: 35
Views: 10,112
Posted By gstullo

What do you mean, "go back to the disconnect and...

What do you mean, "go back to the disconnect and check for 240 there"? How/where do I do this?
12-09-13, 10:58 AM
Replies: 35
Views: 10,112
Posted By gstullo

A = 0 (120 when grounded) B = 0 (120 when...

A = 0 (120 when grounded)
B = 0 (120 when grounded)
C = 240
D = 240
E = 24
F = 240
G = 0
H = 0
12-07-13, 12:24 PM
Replies: 35
Views: 10,112
Posted By gstullo

Will do. I have a wife and two kids so finding a...

Will do. I have a wife and two kids so finding a solid block of time is nearly impossible. I'll post the readings by the end of the weekend.

I did the earlier tests with em heat on and the hp...
12-07-13, 10:34 AM
Replies: 35
Views: 10,112
Posted By gstullo

I do get 24V at E but nothing at A or B

I do get 24V at E but nothing at A or B
12-07-13, 10:30 AM
Replies: 35
Views: 10,112
Posted By gstullo

Sorry that it has taken me this long to reply... ...

Sorry that it has taken me this long to reply...

When I press the probes to the connections indicated in A or B I get nothing. If I touch one of the probes to one of the leads and then to the...
12-01-13, 12:38 PM
Replies: 35
Views: 10,112
Posted By gstullo

Thanks for putting this together. My meter is in...

Thanks for putting this together. My meter is in my storage unit and I will go get it tomorrow (possibly tonight) and run the tests.

Just for clairification: should I just set the thermostat on...
12-01-13, 12:29 PM
Replies: 35
Views: 10,112
Posted By gstullo

And thanks...

and thanks for the help on this... you're saving me a ton of time, frustration, and probably money!
12-01-13, 12:15 PM
Replies: 35
Views: 10,112
Posted By gstullo

Photos here: ...

Photos here:

http://i790.photobucket.com/albums/yy183/gstullo/IMAG1050_zps1a41cd2d.jpg

http://i790.photobucket.com/albums/yy183/gstullo/IMAG1049_zps2b38a5ac.jpg
12-01-13, 11:43 AM
Replies: 35
Views: 10,112
Posted By gstullo

Ok. Then I assume that they are in the top of...

Ok. Then I assume that they are in the top of the Trane TVF024A140A1 unit.

Seeing I do not seem to be getting anything from them in EM Heat mode, I assume that they are bad. Is there a way to...
12-01-13, 11:26 AM
Replies: 35
Views: 10,112
Posted By gstullo

Where are AUX or EM coils/strips located and does my system have them?

Hi,

New to HVAC beyond simply installing new thermostats.

Last night I noticed that my Trane system (with Honeywell RTH7600 thermostat) would blast cold air about ever 20 minutes for a duration...
Showing results 1 to 20 of 20


 
Forum Jump