Search: Posts Made By: geoffv
Showing results 1 to 12 of 12
Search took 0.01 seconds.
02-23-15, 06:34 PM
Replies: 21
Views: 3,224
Posted By geoffv

Thanks for all the info. Think I'll be calling a...

Thanks for all the info. Think I'll be calling a couple heating contractors for quotes. Fact is, the furnace is getting on. There is a bit of a whine in the bearings of the draft inducer motor, whole...
02-22-15, 07:06 PM
Replies: 21
Views: 3,224
Posted By geoffv

OK - turned 1 + 2 on, and no change. Attached...

OK - turned 1 + 2 on, and no change.
Attached is the troubleshooting guide from the control board door -- see the second to last box in the left column - says if blower doesn't stay on:
Check for...
02-22-15, 06:26 PM
Replies: 21
Views: 3,224
Posted By geoffv

By "1 and 2", if you mean the DIP switches, no,...

By "1 and 2", if you mean the DIP switches, no, all three are in the off position.

Just now, following a heating cycle:
- burner shut off
- 6 seconds later blowers shut off
- 35 seconds later...
02-22-15, 05:12 PM
Replies: 21
Views: 3,224
Posted By geoffv

Well, incoming air comes in left side at bottom....

Well, incoming air comes in left side at bottom. Blower at bottom and blows air up over heat exchanger, and hot air exits out the top. Is that horizontal or vertical? (BTW, the photo of the board is...
02-22-15, 03:26 PM
Replies: 21
Views: 3,224
Posted By geoffv

The board in the furnace is model 62-22694-11 -...

The board in the furnace is model 62-22694-11 - see photo. 47031

There is one set of three switches, and I don't see any info about them on the documentation attached to the furnace.
47032
...
02-22-15, 03:17 PM
Replies: 21
Views: 3,224
Posted By geoffv

I think you may be on to something here. Filter...

I think you may be on to something here. Filter is new, but has been a couple of years since a good cleaning.

See the next post re pictures of the board.

Thanks.
02-22-15, 07:41 AM
Replies: 21
Views: 3,224
Posted By geoffv

Thanks guys. So digging a little deeper I...

Thanks guys.
So digging a little deeper I found what I said below (and what I told repair guy) was wrong. What's happening is the call for heat and running of the furnace is fine. After it shuts...
02-21-15, 11:57 AM
Replies: 21
Views: 3,224
Posted By geoffv

Should repair guy actually test parts, or just switch stuff out?

Regarding my Rheem Criterion Furnace (1994), my question is what should I be expecting from the furnace repair guy.

What's happening is on start-up, the draft blower starts, the burners ignite...
Replies: 3
Views: 9,812
Posted By geoffv

Foundation concrete repair - rebar dowels, adhesive, etc

This is a follow-up from this post a while back: http://www.doityourself.com/forum/bricks-masonry-cinder-block-paving-walking-stones-asphalt-concrete/528633-diy-foundation-repair.html

There's a...
Replies: 7
Views: 7,288
Posted By geoffv

Thanks again. The "foundation repairman"...

Thanks again.

The "foundation repairman" came and had a look and quickly wondered how deep the cracks go, what about those other cracks, boy the garage floor sure is cracked, that's an awfully big...
Replies: 7
Views: 7,288
Posted By geoffv

A few more thoughts...

Thanks for the replies gentlemen. Tomorrow I'll excavate deeper and further along the two walls to see what I find.

To repair I'm thinking I'd pull out any of the large pieces that I'm able to...
Replies: 7
Views: 7,288
Posted By geoffv

Is this a DIY foundation repair?

Hi All,

This is the back corner of my garage. Years of poor grading, downspout too close & freeze/thaw.

I'm pretty handy, but not sure if a DIY'r can do an effective repair on this -- see...
Showing results 1 to 12 of 12


 
Forum Jump