Search: Posts Made By: maosla
Showing results 1 to 13 of 13
Search took 0.01 seconds.
Replies: 1
Views: 1,107
Posted By maosla

Lynx Touch Permanent Mounting of control panel

Should the control panel be concealed?
I have my basic system working fine for about a week and now I want to decide where to place the control panel. The primary entry into my home is via the...
Replies: 9
Views: 3,812
Posted By maosla

Great Tip from the PRO; invert the transmitter....

Great Tip from the PRO; invert the transmitter. Thanks again
Replies: 9
Views: 3,812
Posted By maosla

Thank you both. That Loop 2 fixed 1 problem. The...

Thank you both. That Loop 2 fixed 1 problem. The other issues I had was that the magnet could only trigger the sensor from 1 side only. I have 2 entrance doors where one opens to the right the other...
Replies: 9
Views: 3,812
Posted By maosla

Lynx Touch Wireless Programming

Trying to install this alarm. I followed the manual and was able to install three 5816 sensors and the motion sensor. All were found by the panel and the serial numbers are all correct. When I open...
Replies: 3
Views: 1,608
Posted By maosla

Thumbs up Problem solved

I cranked the mower several times with the spark plug removed and then I installed the spark plug and started the mower. It stalled a few times and rang rough at first. a huge cloud of oil smoke...
Replies: 3
Views: 1,608
Posted By maosla

Excellent diagnosis. I came home late and I was...

Excellent diagnosis. I came home late and I was not able to try and start the mower, but I remove the spark plug and the stack pulley spins freely with the plug removed. There was oil on the plug and...
Replies: 3
Views: 1,608
Posted By maosla

Murray rear engine rider won't crank

My mower drive belt came loose last Fall. I drove the mower into my garage and parked it for the winter. 2 weeks ago I jacked up the front, changed the mower belt but left the mower on jack stands. I...
Replies: 2
Views: 8,667
Posted By maosla

Here is a link I found. A child crash her bicycle...

Here is a link I found. A child crash her bicycle into my closed door and the cable on one side came off the cable drum when I tried to opener the door. After straighting some rollers and following...
Replies: 2
Views: 1,165
Posted By maosla

I powered down and upon boot up it cleared the...

I powered down and upon boot up it cleared the zone check error. I am in the process of changing other batteries in the wireless transmitters and I will try your method.
Replies: 2
Views: 1,165
Posted By maosla

Ademco 5816 no signal to vista 20

I have a wireless 16 zones system and 1 window transmitter is not working and is showing up as zone 12 check on 6128 keypad. I changed the battery and it still shows up a check error and I had to...
Replies: 1
Views: 4,391
Posted By maosla

Ademco Vista 20 Error Codes BAT and FC

This week my alarm system has been dialing out when the alarm system is set without the alarm being triggered. I read my manual and BAT means weak system's main standby battery is weak. When I unplug...
Replies: 2
Views: 1,220
Posted By maosla

"Put the belt onto all pulleys possible and then...

"Put the belt onto all pulleys possible and then "walk" or "slip" it onto the last pulley be holding it on the rim of that pulley while turning the pulley".
Thanks for the tip. That is exactly what...
Replies: 2
Views: 1,220
Posted By maosla

Question Changing Drive Belt on Murray 30" rider

I bought a new drive belt, removed the mower deck,followed the owner's manual and removed the old belt which was stretched, put on the new one but I cannot get it over the drive pulley.
The new...
Showing results 1 to 13 of 13


 
Forum Jump