Search: Posts Made By: Doorman2722
Showing results 1 to 23 of 23
Search took 0.03 seconds.
Replies: 13
Views: 387
Posted By Doorman2722

This is pretty much the standard in the US garage...

This is pretty much the standard in the US garage door world Garage door slide lock...
Replies: 11
Views: 253
Posted By Doorman2722

Norm, your down force sounds about right, I do...

Norm, your down force sounds about right, I do the same and run it down on my shoulder to see how hard it's pushing. There are two dials on the circuit board that controls up/down force. I usually...
Replies: 8
Views: 347
Posted By Doorman2722

the peg on the bottom fixture for those style...

the peg on the bottom fixture for those style extension cables are to small for a regular 1/8 inch replacement cable to hook onto. You will need to (1)try and find a replacement directly from the...
Replies: 13
Views: 1,002
Posted By Doorman2722

DO NOT TRY TO REMOVE THE BOTTOM ROLLER BRACKET......

DO NOT TRY TO REMOVE THE BOTTOM ROLLER BRACKET... it is under extream tension and you will get a trip to the emergency room. Stuff the ends of the bottom seal with bubble wrap or foam
Replies: 2
Views: 227
Posted By Doorman2722

Try wiring it directly to the opener with another...

Try wiring it directly to the opener with another piece of short wire, if it still don't work your wall control is probably faulty. They are notorious for going bad and Chamberlian may warranty it if...
Replies: 7
Views: 344
Posted By Doorman2722

That doesn't look like a Finnish coat to me, it...

That doesn't look like a Finnish coat to me, it looks like binder... this link explains it SEE HERE (https://alphapavingtexas.com/asphalt-paving-binder-topcoat/)
Replies: 2
Views: 234
Posted By Doorman2722

Install a keyless entry on the outside jam, you...

Install a keyless entry on the outside jam, you can use it to open the door but when the door is open all you have to do is press the enter button an the door will close.
Replies: 6
Views: 360
Posted By Doorman2722

On that model the sensors are powered down to...

On that model the sensors are powered down to conserve energy when the door is closed. I believe the voltage should be around 5 volts
Replies: 8
Views: 255
Posted By Doorman2722

That's a commercial opener installed before photo...

That's a commercial opener installed before photo eyes, it can have a reversing edge hooked which would be a pneumatic tube ran through the bottom rubber weather seal plumbed into a switch which...
Replies: 24
Views: 4,423
Posted By Doorman2722

Well I asked around in the Garage door world and...

Well I asked around in the Garage door world and no one really has a fix for this other than replacing the hinge with an original, or replace the door. That horman hinge may work for the center...
Replies: 1
Views: 305
Posted By Doorman2722

Are you sure remotes a transmitting? point the...

Are you sure remotes a transmitting? point the remote towards the back of the opener/ circuit board and press and hold the button on the remote... if it is transmitting the LED next to the purple...
Replies: 1
Views: 319
Posted By Doorman2722

Your gonna get a rub with "Dutch corners"it...

Your gonna get a rub with "Dutch corners"it always does, if you fill the new rubber weather seal with something to make it rigid it might help it go bye. You can also put some "slick it"on the wood,...
Replies: 3
Views: 277
Posted By Doorman2722

If the light is flashing, it's an issue with the...

If the light is flashing, it's an issue with the eye sensors. Make sure they are clean, pointed at each other and there is nothing on the door that blocks the sensors as it closes like a rope or...
Replies: 24
Views: 4,423
Posted By Doorman2722

If you can't find one on line check with a Wayne...

If you can't find one on line check with a Wayne Dalton or an Overhead Door Company Dealer, maybe they have one on a shelf somewhere.
Replies: 7
Views: 765
Posted By Doorman2722

Try calling Chamberlain, they manufactured the...

Try calling Chamberlain, they manufactured the opener and branded it for craftsman. Most Liftmaster/ Chamberlain motors have a life time warranty, some have a 5 Year. I believe it is stated in the...
Replies: 15
Views: 957
Posted By Doorman2722

24 quarter turns divided by 4 = 6 turns. A 7 foot...

24 quarter turns divided by 4 = 6 turns. A 7 foot high door requires 7.5 turns that is why your cables come off. Your spring is larger than what is required for the weight of your door that is why...
Replies: 4
Views: 638
Posted By Doorman2722

Yes put a light coat of grease on top and...

Yes put a light coat of grease on top and bottom... Garage door track, NO!
Replies: 37
Views: 1,777
Posted By Doorman2722

aka pedro... no the arm should separate from the...

aka pedro... no the arm should separate from the trolley when you pull the rope. This opener is a Liftmaster commercial opener and that is the way they are designed. Residential the arm will remain...
Replies: 37
Views: 1,777
Posted By Doorman2722

Yep, did you try calling the company who...

Yep, did you try calling the company who installed it, they may warranty their installs? if not have a helper hold the front of the opener up, mark the bolt holes.... unhook the straight arm from the...
Replies: 24
Views: 4,423
Posted By Doorman2722

Looking at you picture again I see your hinge has...

Looking at you picture again I see your hinge has a bend in it, so this may be different. Can you post a picture of it straight on and maybe a picture of a hinge that is not damaged
Replies: 24
Views: 4,423
Posted By Doorman2722

Looks like Wayne Dalton pinch resistant hinge, be...

Looks like Wayne Dalton pinch resistant hinge, be advised there are different sizes depending where they are positioned on the door. Check the number stamped on it....
Replies: 6
Views: 1,351
Posted By Doorman2722

I don't really like the hinge system on Amaar. I...

I don't really like the hinge system on Amaar. I prefer Clopay, CHI, Raynor or Haas. Remember you get what you pay for, anything with a double steel sided section and foam injected will get you a...
Replies: 6
Views: 1,351
Posted By Doorman2722

you can tech screw or rivet through the skin from...

you can tech screw or rivet through the skin from the outside into the mullion to hold it in place, but you will see the screw heads. you might be able to remove the hinge and rivet it back to the...
Showing results 1 to 23 of 23


 
Forum Jump