Search: Posts Made By: mskin
Showing results 1 to 20 of 20
Search took 0.01 seconds.
05-07-09, 07:49 PM
Replies: 6
Views: 1,816
Posted By mskin

whats happening is the while the system is...

whats happening is the while the system is supposed to be "drawing" brine, its actually filling the brine tank back up.
then, it fills it up again during the last cycle (when its supposed to).
...
05-04-09, 06:53 PM
Replies: 6
Views: 1,816
Posted By mskin

thanks. i will give it a shot.

thanks. i will give it a shot.
05-03-09, 06:59 PM
Replies: 6
Views: 1,816
Posted By mskin

The controls for one are 255/440i and the unit is...

The controls for one are 255/440i and the unit is NS-20T. The second controls are 268/440i and the unit is MBA-MM-10-1. The source is well. Water pressure is good out of the tank, poor at the...
05-02-09, 12:31 PM
Replies: 6
Views: 1,816
Posted By mskin

issues after regeneration.

so i just refilled/regenerated my masters NS-20 and then forced a backwash...

my brine tank overflowed. i think this is because i put a new injector in and it was either the wrong size, or...
04-30-09, 09:23 PM
Replies: 5
Views: 4,178
Posted By mskin

this is an awesome product. my vote on this one...

this is an awesome product. my vote on this one too.
Replies: 6
Views: 10,198
Posted By mskin

cut a 1/2" reglet 8" above the deck. bend the...

cut a 1/2" reglet 8" above the deck. bend the flashing 90 degrees so it tucks into the reglet. shove a 1/2" backer rod in the top and caulk it with a good mastic.... i hate this detail, but not...
04-30-09, 08:43 PM
Replies: 5
Views: 811
Posted By mskin

when you say not plumb, do you mean in the...

when you say not plumb, do you mean in the vertical direction? really not good for an exterior wall (specifically on the eave ends). but, you could run horizontal furring strips of varying depth.......
04-30-09, 08:37 PM
Replies: 1
Views: 1,438
Posted By mskin

i would assume you need to install a beam where...

i would assume you need to install a beam where the load bearing wall is to pick up the load of the ceiling joists above. You will be altering how the loads are transferred through the structure. ...
Replies: 3
Views: 1,392
Posted By mskin

any wood in contact with concrete should be...

any wood in contact with concrete should be pressure treated, and should never come in contact with aluminum flashings or fasteners as they will fail. good luck!!
04-27-09, 09:36 PM
Replies: 15
Views: 1,465
Posted By mskin

HotinOKLAHOMA.... i followed that exact...

HotinOKLAHOMA....

i followed that exact procedure 7 years ago. having never worked with PVC liner, cement board, etc... it worked out great. i highly recommend this procedure, its hundreds of...
04-27-09, 09:19 PM
Replies: 6
Views: 1,061
Posted By mskin

i know VCT often fails with a slab on grade...

i know VCT often fails with a slab on grade installation. moisture trying to escape the concrete has nowhere to go and as it pushes up, it eventually de-laminates the tiles and they bubble. Even if...
04-27-09, 08:45 PM
Replies: 10
Views: 2,586
Posted By mskin

i had a similar assembly in my 200 year old...

i had a similar assembly in my 200 year old beast. i sledged the old floor out. i was left with 5'x6' floor plate with a 1" difference between the high and low points. the subfloor was very...
04-27-09, 08:19 PM
Replies: 6
Views: 1,440
Posted By mskin

i used tiger foam slow rise formula. there are a...

i used tiger foam slow rise formula. there are a few other competitors that i could have just as easily chosen. TF had decent customer support. they have a product demo video online you can check...
04-27-09, 01:32 PM
Replies: 6
Views: 1,440
Posted By mskin

i just recently insulated my house (plaster and...

i just recently insulated my house (plaster and lathe) from the inside. i know the arguments to do it from the outside, but i drilled holes in the plaster and shot in an expanding foam. i found a...
Replies: 5
Views: 1,583
Posted By mskin

i have the same problem and the same set up it...

i have the same problem and the same set up it sounds. I put a level on my doors, ad they are level. could be my floor is out of wack. tried playing with the springs (tightening / loosening). ...
04-26-09, 07:01 PM
Replies: 4
Views: 970
Posted By mskin

I guess my point is that in some respects its...

I guess my point is that in some respects its not "how much" but is it done right. its important to keep the insulation away from the sheathing, especially at the eave location. its more...
04-26-09, 06:57 PM
Replies: 4
Views: 970
Posted By mskin

Section 1203 of the 2006 IBC requires the total...

Section 1203 of the 2006 IBC requires the total ventilation to be 1/150 of the of the space being vented. 50% of this venting should be by eave/cornice vents, the balance should be at least three...
04-22-09, 07:06 AM
Replies: 6
Views: 1,852
Posted By mskin

Hi andy, i do replace the salt in the Brine. ...

Hi andy,
i do replace the salt in the Brine.

i discovered after talking with Masters the solution is Magnesium Calcite... i dont know if that makes a difference or not.
04-21-09, 07:08 PM
Replies: 6
Views: 1,852
Posted By mskin

the reason i'm not starting from the beginning is...

the reason i'm not starting from the beginning is because i have what appears to be a perfectly fine water filtration system that's not working correctly due to neglect. I've had a few water tests. ...
04-20-09, 09:21 PM
Replies: 6
Views: 1,852
Posted By mskin

issues with filtration

i've had a master water system installed for six years and it's never worked well. i blame the installation, lack of info from installer, and subsequent lack of service... i do not blame the...
Showing results 1 to 20 of 20


 
Forum Jump