Search: Posts Made By: jklsdf
Showing results 1 to 18 of 18
Search took 0.01 seconds.
Replies: 1
Views: 319
Posted By jklsdf

3 way switch trouble shooting: No continuity in the traveler wire

Hello,

I have a set up with a 3 way switch (A) and a dimmer (B) controlling hallway lights (see attached picture).

The switches were working fine both ways (as a three way should), till...
07-25-19, 07:29 AM
Replies: 3
Views: 476
Posted By jklsdf

Thanks Pete. The 16 AWG is not available, Can I...

Thanks Pete.
The 16 AWG is not available, Can I use 14 awg. The wire has to be vw-1 and awm rated to 105 deg C

JK
07-24-19, 03:37 PM
Replies: 3
Views: 476
Posted By jklsdf

wire guage/type for Carrier blower circuit board

Hello,

My hvac blower fan was not working, so I replaced the circuit board (hk42fz009 to a new one ICM282A). Everthing runs fine, however, since the configuration of the new board is different,...
05-27-19, 01:50 PM
Replies: 6
Views: 1,388
Posted By jklsdf

********SOLVED********** Thanks so much for...

********SOLVED**********

Thanks so much for all the replies. I really appreciate it.

I spent 5 hours digging around to see if the common white wire was spliced etc. I also had installed stakes...
05-27-19, 09:34 AM
Replies: 6
Views: 1,388
Posted By jklsdf

Okay, Here is what I tried: I dsiconnected zone...

Okay, Here is what I tried: I dsiconnected zone two wire. I manually turned on zone one, there is 29 VAC between common white wire and zone one wire (as should be). HOWEVER, there is 29 VAC between...
05-26-19, 10:04 PM
Replies: 6
Views: 1,388
Posted By jklsdf

Sprinklers won't turn on

Hello:

I was wondering if anyone can help me?

I have a 12 zone orbit sprinkler timer, which didn't turn on. I tried manual, but it says on the timer, its running, but the valve don't turn on.
...
03-29-19, 11:51 AM
Replies: 2
Views: 378
Posted By jklsdf

Just realized that it possibly is a screw in...

Just realized that it possibly is a screw in joint (the box you referred to is a multiport valve). I will have to check the manual again to make sure.

The issue also is that it has been around for...
03-29-19, 08:43 AM
Replies: 2
Views: 378
Posted By jklsdf

Pump plumbing dilemma

I am replaceing a very old wfds-8 whisperflo 2 hp with a newly bought intelliflo pump. I had earlier thought about replacing the backend only....however the volutes are different as my whisperflo is...
02-23-19, 02:48 PM
Replies: 2
Views: 709
Posted By jklsdf

Thanks Pjmax. I appreciate your time and reply. ...

Thanks Pjmax. I appreciate your time and reply.
JK
02-21-19, 12:42 PM
Replies: 2
Views: 709
Posted By jklsdf

New 12 awg gauge wires for 2 hp pool pump

I am replacing my 2 hp pentair pool pump with the exact same model (so all wiring etc remain the same).

While removing the old motor I noticed that the old 12 awg wires were extremely rigid with...
09-14-18, 09:24 AM
Replies: 4
Views: 498
Posted By jklsdf

OP here... I replaced the capacitor, but the...

OP here...

I replaced the capacitor, but the fan would not turn on. Next I replace the motor, and now it is running and cooling. So far so good.

I appreciate the forum and moderator's advice.
...
09-01-18, 05:41 PM
Replies: 4
Views: 498
Posted By jklsdf

condensor fan moves freely, but seizes when compressor turns on

Hello,
I wonder if anyone can help trouble shoot this scenario.

HVAC system has been fine all summer, but today the room temp started rising. I checked the outside unit and the fan was not moving...
Replies: 10
Views: 1,404
Posted By jklsdf

I tried the master code to stop the alarm and it...

I tried the master code to stop the alarm and it works.
Thanks for your help RonFL
Replies: 10
Views: 1,404
Posted By jklsdf

Okay, so I called the old monitoring company and...

Okay, so I called the old monitoring company and got the Installer code, and it works.

I saw the wiring for the smokes, it is aux, pgm1, common and zone 8.

What can I do to make sure the...
Replies: 10
Views: 1,404
Posted By jklsdf

No I just have the master code. Is there a way to...

No I just have the master code. Is there a way to find an installer code hidden somewhere. I called the company who installed it for the previous homeowners, but since the record is in someone else's...
Replies: 10
Views: 1,404
Posted By jklsdf

Thanks MrRonFL: So if the system isnt...

Thanks MrRonFL:

So if the system isnt properly configured, what is my option?

Thanks for the manual, maybe I will find some help in there.

jklsdf
Replies: 10
Views: 1,404
Posted By jklsdf

Thanks Pete for your reply. I can enter the...

Thanks Pete for your reply.

I can enter the code, but what does "off" mean. Sorry for my ignorance. But I appreciate your reply.
Replies: 10
Views: 1,404
Posted By jklsdf

dsc832 pc5010 ...cannot silence fire alarm by pressing # or resetting by *72

hello:

I am new to the community.

I have a dsc832/pc5010 home alarm system with 10 smoke detectors (eight falcon 545T and 2 DSC 410bst).

I am trying to replace the smokes, as they are way...
Showing results 1 to 18 of 18


 
Forum Jump