Search: Posts Made By: Astuff
Showing results 1 to 18 of 18
Search took 0.01 seconds.
12-11-20, 11:35 AM
Replies: 12
Views: 209
Posted By caddymac

If the transformer is the same for both...

If the transformer is the same for both baseboards, you might be able to do some interesting things to keep them separated yet still controlled by the same thermostat.

If the thermostat lets you...
12-08-20, 12:49 PM
Replies: 5
Views: 130
Posted By petethebuilder

.... nevermind , , , , , , ,

.... nevermind

,
,
,
,
,
,
,
08-25-20, 11:02 AM
Replies: 4
Views: 195
Posted By Zorfdt

I would give the Power company a call. ...

I would give the Power company a call. Technically the weatherhead isn't their responsibility, but if they have crews in the area, they might go up and screw it in for you.

I know they have...
06-09-20, 10:27 PM
Replies: 23
Views: 429
Posted By dmartura

Relay Wiring

Please see the picture I just created. Is this right or do I have it backwards?
04-10-20, 09:35 PM
Replies: 8
Views: 308
Posted By joed

The service would need to be upgraded. The wiring...

The service would need to be upgraded. The wiring from the meter to the current panel would sized for the current panel not the extra load you are planning to add.
04-07-20, 03:56 PM
Replies: 6
Views: 316
Posted By pcboss

Can you post a picture from further back? ...

Can you post a picture from further back?

Secondly, that panel looks like it is toast and needs replacement.
03-21-20, 01:31 PM
Replies: 11
Views: 511
Posted By PJmax

Ok..... I modified the diagram for that model...

Ok..... I modified the diagram for that model based on your installation.
The purple jumper between G and Y can be any type of wire.... even bare.
The H in the circle is the humidifier solenoid.
...
02-21-20, 12:07 PM
Replies: 8
Views: 332
Posted By Zorfdt

No issue with using a higher-amperage breaker in...

No issue with using a higher-amperage breaker in the subpanel. It's just there as a disconnect.
The important over-current protection device is the 60A breaker in your main panel that's sized to...
01-07-20, 12:34 PM
Replies: 23
Views: 589
Posted By Dan1973

So, they don't have phones (good for you, by the...

So, they don't have phones (good for you, by the way!) or tablets or electronics that you can take away. But surely each kid has a "currency" - something that is important to him/her. Maybe it's an...
12-19-19, 12:14 PM
Replies: 12
Views: 527
Posted By manden

I cannot find any info on it but it should be...

I cannot find any info on it but it should be reading RMS.
So I still say trash it.
12-12-19, 06:18 PM
Replies: 13
Views: 738
Posted By CasualJoe

The intent of CTL tandem breakers is to keep the...

The intent of CTL tandem breakers is to keep the user from installing more circuits than the panel was designed for. I suspect that an Eaton engineer made the decision that since this was a 12-24...
11-05-19, 02:48 PM
Replies: 2
Views: 277
Posted By joed

It won't give you 24ah. It will still be 12 ah...

It won't give you 24ah. It will still be 12 ah unless you also parallel the 6 volt battery with another 12 ah.
10-30-19, 06:09 AM
Replies: 4
Views: 419
Posted By pattenp

60A is most likely HVAC system.

60A is most likely HVAC system.
09-10-19, 05:42 PM
Replies: 7
Views: 378
Posted By pattenp

Does the afci breaker you have also provide...

Does the afci breaker you have also provide ground fault protection?
See this... https://www.jadelearning.com/combination-arc-fault-circuit-breaker-vs-dual-function-arc-fault-gfci-circuit-breaker/
07-15-19, 06:03 PM
Replies: 5
Views: 1,013
Posted By CasualJoe

Looks to me like this would be a great...

Looks to me like this would be a great application for GFCI receptacles rather than GFCI breakers.
07-01-19, 11:32 AM
Replies: 5
Views: 633
Posted By AllanJ

You can take an ohmmeter and check for continuity...

You can take an ohmmeter and check for continuity between the two hot pins (one at a time) of the original plug and exposed metal parts on the iron itself. Ther should not be continuity. Then you can...
06-10-19, 10:57 AM
Replies: 21
Views: 3,230
Posted By karwoda

You are better off replacing that control board...

You are better off replacing that control board with a newer one that allows for independent zone control. I had a similar board, except mine was EWC-ST-2E. I replaced it with an EWC NCM300 and was...
05-28-19, 06:00 PM
Replies: 5
Views: 806
Posted By Marq1

What ever you do for the winter just dont wrap in...

What ever you do for the winter just dont wrap in plastic.

You can cut a piece of plywood to the same general size/shape and place that on top to keep coils clean but still allow air flow!
Showing results 1 to 18 of 18


 
Forum Jump