Search: Posts Made By: Ron53
Showing results 1 to 23 of 23
Search took 0.02 seconds.
Replies: 10
Views: 365
Posted By Ron53

The "button" in your third picture looks to be...

The "button" in your third picture looks to be the unlocking pin, it should pull outward and turn to line up the pin in it to hold it in the out position. With the zero experience you have I'm...
Replies: 13
Views: 400
Posted By Ron53

You might want to take the worn out latch and...

You might want to take the worn out latch and drill a hole through the area where the "pinch" is located and install a hardened roll pin in it's place. It may require modifying the opening in the...
12-27-20, 09:28 AM
Replies: 7
Views: 306
Posted By Ron53

https://cimg4.ibsrv.net/gimg/www.doityourselft.com...

https://cimg4.ibsrv.net/gimg/www.doityourselft.com-vbulletin/720x960/no_chew_deterrent_70da901506d8f7a19835fbfd216079df7930bd9e.jpg

Just don't try using this stuff.
Replies: 25
Views: 634
Posted By Ron53

Norton IS a virus. Had it on one of my desktops...

Norton IS a virus. Had it on one of my desktops and tried to uninstall it but I never got it completely removed and had to reformat my hard drive to finally get rid of it. Nothing with the name...
11-23-20, 08:42 AM
Replies: 8
Views: 308
Posted By Ron53

Don't you have a city water meter outside...

Don't you have a city water meter outside somewhere? Usually there is a shut off valve near the meter.
09-27-20, 12:30 PM
Replies: 11
Views: 908
Posted By Ron53

Compound bows have the string length and the...

Compound bows have the string length and the cable length on the information sticker on the bow. I have always used Zebra strings and cables on my bows, they are a little pricey but are very good...
Replies: 6
Views: 263
Posted By Ron53

The only thing it would be useful for is a...

The only thing it would be useful for is a planter in your front yard. Send it back.
Replies: 6
Views: 293
Posted By Ron53

If those were the first boards he installed on my...

If those were the first boards he installed on my deck I would fire him on the spot. I think his poor work and attitude will continue and the rest of the install has the strong possibility up being...
Replies: 2
Views: 119
Posted By Ron53

Just mark the old screw locations in the new...

Just mark the old screw locations in the new plate, drill holes in plate to match up with old screw locations and it will be fine.
Replies: 6
Views: 417
Posted By Ron53

You still have air in the system.

You still have air in the system.
Replies: 65
Views: 1,758
Posted By Ron53

As a side note, always buy NAME BRAND WIRE never...

As a side note, always buy NAME BRAND WIRE never any generic or HF crap. You can thank me later.
05-01-20, 02:04 PM
Replies: 10
Views: 1,340
Posted By Ron53

I'm surprised people still think it's a good idea...

I'm surprised people still think it's a good idea to even get a refund. I adjusted my taxes years ago to reflect breaking even or at least very close with both the State and the IRS.
Replies: 17
Views: 530
Posted By Ron53

I know what they are made of that's why I said I...

I know what they are made of that's why I said I think they would be too slick for that use, but have at it. I would be extra careful using that jack if you go that route though.
10-25-19, 04:34 PM
Replies: 22
Views: 1,524
Posted By Ron53

Joe, the fire in Northern CA was started by a PGE...

Joe, the fire in Northern CA was started by a PGE tower that failed, and they didn't get the power turned off fast enough. What I heard about the one in SOCAL was from someone putting hot coals out...
10-25-19, 11:01 AM
Replies: 22
Views: 1,524
Posted By Ron53

One of the biggest issues is that for the past 30...

One of the biggest issues is that for the past 30 or 40 years the wacko enviromentalists have prevented any fuel reduction anywhere in CA. If it keeps up there won't be any fire issues after...
Replies: 16
Views: 837
Posted By Ron53

Instead of doing all of that, maybe you could...

Instead of doing all of that, maybe you could just top off the tank everytime your finished mowing.
Replies: 3
Views: 779
Posted By Ron53

Probably a mis-drilled screw hole, if you can get...

Probably a mis-drilled screw hole, if you can get to it maybe screw a short sheet metal screw into it. And seal it with a little silicone sealer on the screw before installing it.
Replies: 30
Views: 1,903
Posted By Ron53

Good grief, you could have had it all done by...

Good grief, you could have had it all done by now! If it makes it easier measure each piece you intend to replace and cut out a duplicate piece, install it, move to next piece. Someone once told me:...
06-19-19, 12:15 PM
Replies: 7
Views: 1,440
Posted By Ron53

You could cut and paste the link on Amazon or any...

You could cut and paste the link on Amazon or any othere site that sells traps. And if you go that route use peanut butter as bait, works very well.
06-18-19, 08:21 AM
Replies: 7
Views: 1,440
Posted By Ron53

Get yourself one of these traps, even though they...

Get yourself one of these traps, even though they look like they would be too small they work great. Havahart 0745 One-Door Animal Trap for Chipmunk, Squirrel, Rat, and Weasel, X-Small..
Replies: 9
Views: 627
Posted By Ron53

Yes, that TOTO is a very good toilet. Used them...

Yes, that TOTO is a very good toilet. Used them for many years with no issues what so ever. But I would make sure to get the 1.6 gal flush model.
Replies: 10
Views: 582
Posted By Ron53

No, Bronze bushings have been around forever and...

No, Bronze bushings have been around forever and will last just as long if not longer than roller bearing. And yes the grease trick works well for removing them.
Replies: 2
Views: 462
Posted By Ron53

How long is a long time? My 30 gal tank takes a...

How long is a long time? My 30 gal tank takes a while to fill, I have never timed it but it doesn't fill all that fast and it's only a year old. And the pipe getting hot is normal for all compressors.
Showing results 1 to 23 of 23


 
Forum Jump