Search: Posts Made By: nedrierson78
Showing results 1 to 20 of 20
Search took 0.01 seconds.
03-04-10, 01:28 PM
Replies: 9
Views: 3,897
Posted By nedrierson78

Mine were the same. I just cut the white and...

Mine were the same. I just cut the white and black wires (inside the light housing) and hard wired them in.

They work great.
02-25-10, 11:47 AM
Replies: 1
Views: 743
Posted By nedrierson78

Drain size for upstairs laundry? 1 1/2" or 2"?

I'm moving my laundry up stairs for convenience. What size drain pipe do people recommend? 1 1/2" or 2"?

I'd rather run 1 1/2", but wanted to see what your opinions might be.

What is code?
...
01-25-10, 10:21 PM
Replies: 4
Views: 996
Posted By nedrierson78

Thanks for the replies. House is in MN, so...

Thanks for the replies. House is in MN, so radiant floor heat is a must. The tile gets very cold in the winter.

Yes, I will be updating all the electrical. Like I said earlier, this bath DOES NOT...
01-25-10, 01:41 PM
Replies: 10
Views: 8,298
Posted By nedrierson78

I like the cold rolled steel idea. Would you have...

I like the cold rolled steel idea. Would you have any pics of what you are referring to?

I'm assuming 1/2" thick by 2" wide is the measurements you are referring to.
01-25-10, 01:32 PM
Replies: 4
Views: 996
Posted By nedrierson78

Help designing a bathroom remodel

I am looking for some help re-designing our bathroom. It is in need of a remodel. The original finish is still in place from when the house was built in 1942. Problems include tight space, lack of...
01-24-10, 07:29 PM
Replies: 4
Views: 1,306
Posted By nedrierson78

I just did a kitchen with 12" granite tiles. We...

I just did a kitchen with 12" granite tiles. We decided on a 1/8" grout joint. I was concerned that the smaller grout line (1/16") would not hold grout, and then would be difficult to get looking...
01-24-10, 07:23 PM
Replies: 13
Views: 12,540
Posted By nedrierson78

I just had the same decision to make. I decided...

I just had the same decision to make. I decided to continue the backsplash to 6" behind the fridge. Looks fine, and nobody notices it but me. I definitely would not take the time to tile behind the...
01-06-10, 08:52 PM
Replies: 10
Views: 8,298
Posted By nedrierson78

I tried to post pics, but that obviously didn't...

I tried to post pics, but that obviously didn't work.

If anybody could point me to a FAQ on that I can include pics.
01-06-10, 08:48 PM
Replies: 10
Views: 8,298
Posted By nedrierson78

The top will be approx 80" long by 18" wide, with...

The top will be approx 80" long by 18" wide, with an overhang of 12".
01-06-10, 08:28 PM
Replies: 10
Views: 8,298
Posted By nedrierson78

Help installing granite bar top.

Looking to install a granite bar top. Structure is a 2x4 wall, framed 16" OC. Any suggestions? How many supports do I need? What type of adhesive?
...
01-03-10, 06:26 PM
Replies: 1
Views: 1,415
Posted By nedrierson78

PEX. Is crimping or expanding better?

I have been plumbing many projects with PEX for a few years. I'm not a licensed plumber.

I have been using Crimp fittings with my PEX applications and am considering a switch to the expander...
12-20-09, 07:57 PM
Replies: 9
Views: 3,897
Posted By nedrierson78

Best under cabinet lighting for kitchen?

I just remodeled my kitchen and wired in a seperate switch for under cabinet lighting (multiple lights). Now I'm looking to buy the lights. Can anybody recommend a good under cabinet light?

I'd...
Replies: 1
Views: 5,855
Posted By nedrierson78

Looking for help installing Honeywell 958 overhead door sensor

Hello,
I am looking for help installing a Honeywell 958 overhead door sensor. I bought the sensor, and no instructions came with it indicating how to install it.

Can anybody help? I can't figure...
Replies: 5
Views: 9,714
Posted By nedrierson78

Thanks for the input. I put a resistor on Zone 1...

Thanks for the input. I put a resistor on Zone 1 and removed my PIR from that zone. The "Fire Trouble 01" is gone.

Now I have a "CHECK 100 RF RECEIVER" fault...

Thanks again for the assistance.
Replies: 5
Views: 9,714
Posted By nedrierson78

NO smokes installed whatsoever. I only have 1...

NO smokes installed whatsoever. I only have 1 wireless transmitter and 1 motion sensor installed for now.
Replies: 5
Views: 9,714
Posted By nedrierson78

Vista 20P "Fire Trouble 01" + "Fault 09"

I'm new to alarms, and installing my first full system in my own house.

I am attempting to stumble through programming the keypad. I can't get past these two faults...

"Fire Trouble 01"
"Fault...
02-08-09, 01:02 PM
Replies: 5
Views: 11,479
Posted By nedrierson78

I bought a house built in 1942 and it had the...

I bought a house built in 1942 and it had the same problem with the galvanized steel. Those pipes are crap. I tried replacing sections here and there where they were accessible, but the low hot water...
Replies: 3
Views: 1,761
Posted By nedrierson78

I assigned 16 to the keypad and now it works. Now...

I assigned 16 to the keypad and now it works. Now the fun of trying to program... Thanks.
Replies: 3
Views: 1,761
Posted By nedrierson78

A follow up to the previous message. I took the...

A follow up to the previous message. I took the basic numeric keypad downstairs and ran it directly to the panel. I get the same problem, a blank screen. When it powers up, I get lights on the...
Replies: 3
Views: 1,761
Posted By nedrierson78

Wiring question Ademco Vista 20P and 6270 AUI touchscreen

Hello,
I am new to this board, so please be patient if I ask a dumb question.

I am installing a new Honeywell Ademco Vista-20P security system.

What is the correct wiring for 2 control panels?...
Showing results 1 to 20 of 20


 
Forum Jump