Search: Posts Made By: Dave Maher
Showing results 1 to 16 of 16
Search took 0.01 seconds.
12-31-20, 02:06 PM
Replies: 3
Views: 228
Posted By Dave Maher

Please give me some ides how to correct this crawlspace.

Give me some ideas how to correct this. A rear single story addition was added to our home before we bought it around 1988. It was built on sonotube's rather than traditional footings and block....
Replies: 0
Views: 131
Posted By Dave Maher

2018 Rogue 38k U0284 and Battery dash light, where to begin?

I have a 2018 Nissan Rogue just out of Warranty. The Check Engine light (U0284) and the Battery light popped up on the dash the same time. Where do I begin?

This code is very vague online for...
Replies: 3
Views: 823
Posted By Dave Maher

Are these Tecumseh Snowblower Engines interchangeable?

Are these two engines interchangable?
HSSK55-67501B and LH195SP-67514D. I have been looking all over the NET and haven't found anything.

Thanks
Replies: 3
Views: 1,558
Posted By Dave Maher

Snapper I6223 Plastic auger bearings! Plastic, what were they thinking

I have a snapper I6223 snowblower. It has plastic bearings on the auger. I caught a news paper in the driveway, and the bearing broke in 3 pieces. Are there alternatives than to put the plastic junk...
Replies: 5
Views: 9,977
Posted By Dave Maher

I am still looking for info on servicing the...

I am still looking for info on servicing the hydro end of this machine. Any one have any ideas?
Replies: 5
Views: 9,977
Posted By Dave Maher

Honda Hs622 leaking axle seals

I got a new cable for the auger. Now i'm just looking for info on replacing the axle seals and servicing the hydrostatic drive end.
Replies: 5
Views: 9,977
Posted By Dave Maher

I have the part numbers. I am wondering whats...

I have the part numbers. I am wondering whats involved in changing the seals.
Replies: 5
Views: 9,977
Posted By Dave Maher

Honda Hs622 Snowblower Seals leaking on drive. Need advice

Believe it or not I just just found this Honda Hs622 snowblower in the garbage. The only wrong with it is the cable that engages the auger snapped and the seals for the drive shaft leak. This is all...
Replies: 1
Views: 1,707
Posted By Dave Maher

Craftsman pressure washer, No water?

Greetings,

I have a Craftsman 2000 psi pressure washer model 580.761800. There is no water on the pressure side of the pump. The engine runs great but no water. I'm going to check the water inlet...
Replies: 7
Views: 3,759
Posted By Dave Maher

No white snow. It was black, from the sprocket...

No white snow. It was black, from the sprocket from that was chewed up. I don't think the parts are available anymore though.
Replies: 7
Views: 3,759
Posted By Dave Maher

That is in fact the sprocket thats chewed up, but...

That is in fact the sprocket thats chewed up, but it is no longer available to purchase. I'm looking for maybe something aftermarket to repair it.
Replies: 7
Views: 3,759
Posted By Dave Maher

Craftsman Opener 139.664053 bad sprocket, need help..

I have a Craftsman 139.664053 opener that the sprocket just went bad on. I looked online and at sears parts (discontinued parts) and I'm alittle confused as to which parts I need to make the repair....
Replies: 3
Views: 3,430
Posted By Dave Maher

Need engine help 86 WALKER w/ 11hp Briggs

I have a 86 Walker mower serial# 8617554 with an 11hp Briggs (model 254427 Type 0124-01 Code 86041711) I purchased this new in 86. The engine is starting to burn oil, smoke etc. I really would like...
Replies: 2
Views: 938
Posted By Dave Maher

Thanks for the reply so fast. I was just really...

Thanks for the reply so fast. I was just really concerned that it might have been a governor issue. It runs really well considering its been sitting awhile. It just had me concerned that the rpm's ...
Replies: 2
Views: 938
Posted By Dave Maher

10Hp B&S I/C Throttle Help

I was just given a 36" Kees Walkbehind Model 361100. It has a 11hp Briggs I/C Model 253702 Type 0020-01 Code 86041610. It has been sitting in a garage for the past couple of years (with a half tank...
Replies: 2
Views: 18,001
Posted By Dave Maher

Tecumseh 8hp Snow King Parts Help..

Hello Everybody,
I just happened to stumble accross this site and "WOW" , Boy am I glad I did..
My Dad felt the need to upgrade snowblowerI am the happy recipient of "Old Faithful" an MTD 8hp...
Showing results 1 to 16 of 16


 
Forum Jump