Search: Posts Made By: mithalas
Showing results 1 to 15 of 15
Search took 0.01 seconds.
06-15-11, 08:43 PM
Replies: 12
Views: 1,917
Posted By mithalas

Test Results

Okay got my results back and am looking for good recommendations on what to do to clean this up. Looking for the best thing to do and a couple steps below that if any. Need to look at all options and...
06-03-11, 06:38 PM
Replies: 12
Views: 1,917
Posted By mithalas

Getting water test

I'm getting tests run on the water from a lab with the following checks plus looking for tannins. Once I get the results I hope you don't mind if I come back and ask for recommendations on what to...
06-01-11, 06:27 PM
Replies: 12
Views: 1,917
Posted By mithalas

System settings

Just for note this system has only been in since Oct 2010, and yes the iron is completely visible if you draw the water pre-system and tastes like your sucking on metal, and I do need a more thorough...
05-31-11, 01:48 PM
Replies: 12
Views: 1,917
Posted By mithalas

Question Still getting lots of red (iron) at the tap

System
Control: Fleck 9100sxt
Resin: Fine mesh 3 cu ft/tank
Tanks: 13x54 (X2)
Filters: 20in 5m, 20in 1m (pre-filtering) floss

water test
Iron 2 PPM
PH 7
Hardness of 4 GPG
04-11-11, 02:28 PM
Replies: 1
Views: 1,152
Posted By mithalas

DLFC washer question

I'm trying to figure out what the flow rate of a DLFC washer that has the marking of 400 on it would be. I'm guessing it would be 4gpm since I ordered a 2gpm washer through a local company and it...
02-12-11, 08:19 AM
Replies: 24
Views: 5,938
Posted By mithalas

okay the restrictor was labeled with a 4 that...

okay the restrictor was labeled with a 4 that coincides with 2.4gpm.. The upper distributor basket in the one tank looked great and was in place. What was figured by the company I had come out was...
02-05-11, 12:36 PM
Replies: 24
Views: 5,938
Posted By mithalas

I received an email back saying that they would...

I received an email back saying that they would have changed the setting before shipping. I'm looking for a local dealer to come and look at the system and check it out at this point, because I'm at...
02-05-11, 11:24 AM
Replies: 24
Views: 5,938
Posted By mithalas

The reason for the fine mesh is iron, however I...

The reason for the fine mesh is iron, however I run my water through 5 micron and a 1 micron floss filter (20") before it gets to the softener. I don't have a flow problem into the house at all. I...
02-04-11, 02:09 PM
Replies: 24
Views: 5,938
Posted By mithalas

hmm, 2.5cu ft they gave me 3 per tank to use. ...

hmm, 2.5cu ft they gave me 3 per tank to use. I'll be popping the head tomorrow on the secondary tank and checking the baskets (they are fine slotted). If there is 3 in each tank it will push some...
02-02-11, 12:20 PM
Replies: 24
Views: 5,938
Posted By mithalas

BW rate

I hope what you were asking for was the backwash rate because that was my understanding.


Okay the backwash rate according to the place I purchased from is 2.5gpm.

Thanks

Michael
02-01-11, 05:48 PM
Replies: 24
Views: 5,938
Posted By mithalas

I have no turbulators as I have fine mesh resin....

I have no turbulators as I have fine mesh resin. :) I'll be checking the upper baskets this weekend now to see if they've given up the ghost.
02-01-11, 05:29 PM
Replies: 24
Views: 5,938
Posted By mithalas

Thanks

Since I can't find anything that has change except the weather, and my pressure gauge is not working, I've backed off the pressure trigger on my well a little bit and will pull the head off the tanks...
02-01-11, 04:24 PM
Replies: 24
Views: 5,938
Posted By mithalas

Since I ordered it all at one time I would hope...

Since I ordered it all at one time I would hope that they sent the right screens with it. Each tank has a screen at the top that was twist locked in, and the riser tubes have screens at the bottom...
02-01-11, 02:28 PM
Replies: 24
Views: 5,938
Posted By mithalas

I should have included

I do not get any resin in the water lines. I have verified that there is none in any of the sinks or in the hot water tank.
02-01-11, 11:31 AM
Replies: 24
Views: 5,938
Posted By mithalas

Question Resin being flushed out during regen on a Fleck 9100SXT

I have a Fleck 9100sxt with the following specs, and during regen I get about 1-2 cups of resin on the ground afterwords. The system was installed by me about november of 2010 and I didn't notice...
Showing results 1 to 15 of 15


 
Forum Jump