Search: Posts Made By: noma4jon
Showing results 1 to 16 of 16
Search took 0.01 seconds.
07-21-15, 09:28 PM
Replies: 16
Views: 6,479
Posted By noma4jon

are you using LED rope lights? I have encountered...

are you using LED rope lights? I have encountered this problem with LED light strings on some switched outlets, they use so little current that they will remain dimly lit when switched off, I even...
05-17-15, 09:39 PM
Replies: 10
Views: 1,011
Posted By noma4jon

Its not the phone company, its a forum of...

Its not the phone company, its a forum of collectors of classic telephone equipment, including telephone switching machinery with step relays, if you know the brand and model they may even have some...
05-16-15, 01:17 PM
Replies: 10
Views: 1,011
Posted By noma4jon

you might try the folks at Classic Rotary Phones...

you might try the folks at Classic Rotary Phones Forum, some of them have reconnected telephone switch board equipment and there is a board just for telephone switching equipment...
02-26-15, 04:31 PM
Replies: 6
Views: 1,032
Posted By noma4jon

That particular switch is only rated for 120 volt...

That particular switch is only rated for 120 volt 60hz systems, it will not work for UK wiring
12-13-14, 09:39 AM
Replies: 14
Views: 3,578
Posted By noma4jon

It works just fine with both leds or incans, yes...

It works just fine with both leds or incans, yes it does put out dc, usually chaser sets are 140 lights with 4 channels of 35 lights each, as long as you do not exceed 3 amps total it will work just...
12-12-14, 09:37 PM
Replies: 14
Views: 3,578
Posted By noma4jon

I have done this before, its really quite simple....

I have done this before, its really quite simple. There are actually 4 channels, so you have 4 different hot leads and one common neutral return. What I did is I took four standard female plugs used...
10-17-14, 08:54 PM
Replies: 6
Views: 941
Posted By noma4jon

yes it will work just fine. I have a sub panel...

yes it will work just fine. I have a sub panel setup that uses a double pole 50 amp GFCI breaker and there is no nuscience tripping when using individual 120 volt loads from the subpanel. the breaker...
10-12-14, 06:49 PM
Replies: 11
Views: 1,099
Posted By noma4jon

unless the panel is a ITE pushmatic, the AFCI...

unless the panel is a ITE pushmatic, the AFCI breakers manufactured by Siemens are a direct replacement for this panel if he is looking for AFCI protection.
09-03-14, 09:51 PM
Replies: 4
Views: 7,443
Posted By noma4jon

the exposed winding you speak of is a speed coil,...

the exposed winding you speak of is a speed coil, with the red and yellow wires connecting through a two speed switch to select speed, so essentially you have high and low speeds. Is the opening for...
05-12-14, 05:00 PM
Replies: 16
Views: 2,223
Posted By noma4jon

the switch that you have will not work with your...

the switch that you have will not work with your system, it would only cause more damage and burn out the relay coils. if you take a look at the kyle switch plate web site they show you which...
05-10-14, 05:52 PM
Replies: 16
Views: 2,223
Posted By noma4jon

yup, low voltage relay system, looks like Bryant...

yup, low voltage relay system, looks like Bryant or GE, more info on these can be found here
Old Low Voltage Lighting System Switches, Relays, Wall Switch Plates...
06-28-13, 03:12 PM
Replies: 6
Views: 1,493
Posted By noma4jon

Its a condulet fitting. its meant to fit on a...

Its a condulet fitting. its meant to fit on a conduit fitting such as you would find used to form a t or a 90 degree bend in conduit runs. There were also later u ground versions made with the...
03-23-13, 08:26 PM
Replies: 15
Views: 47,349
Posted By noma4jon

It really is amazing how a little time up front...

It really is amazing how a little time up front can save alot of time in the future. Really, a homeowner should know their mechanical and electrical systems and make a list of this information as...
06-29-11, 10:28 PM
Replies: 46
Views: 7,043
Posted By noma4jon

It sounds more like a bi-metalic thermal...

It sounds more like a bi-metalic thermal protection switch that has burned out, I have seen them in the form of a glass bulb with wire leads on the end and they look alot like a miniture christmas...
03-25-11, 08:46 PM
Replies: 15
Views: 1,342
Posted By noma4jon

Thanks for the welcome. I collect all sorts of...

Thanks for the welcome. I collect all sorts of old electrical devices, light sockets and plugs. I also collect christmas lights as well! In fact, I have the exact same tri-tap right next to my...
03-24-11, 07:13 PM
Replies: 15
Views: 1,342
Posted By noma4jon

the M stands for Mono Watt, which at one time was...

the M stands for Mono Watt, which at one time was a ge subsidiary
Showing results 1 to 16 of 16


 
Forum Jump