Search: Posts Made By: GWIZ
Showing results 1 to 25 of 200
Search took 0.03 seconds.
03-12-08, 01:14 PM
Replies: 3
Views: 1,027
Posted By GWIZ

2.0A is the same as 2000ma 350ma is not...

2.0A is the same as 2000ma

350ma is not enough.

3.3 volts tells me more then likely the power pack has a built in voltage regulator.

I would say you need to get the exact one. and note the...
02-28-08, 12:55 AM
Replies: 8
Views: 4,675
Posted By GWIZ

That's not right. *** R = V I or 3...

That's not right.
***

R = V I or 3 volts divided by 6.5 amps = 0.46 ohms.

3 volts times 6.5 amps = 19.5 watts.

You need about a 1/2 ohm resistor, rated higher then 20 watts.
BUT...
02-27-08, 08:42 PM
Replies: 17
Views: 3,461
Posted By GWIZ

When I first read this I assumed hair dryer, why...

When I first read this I assumed hair dryer, why would some one take a shower with a hair dryer.

I will assume clothes dryer.
If your dryer is sending power into the plumbing. Your dryer may have...
02-19-08, 01:02 AM
Replies: 11
Views: 3,782
Posted By GWIZ

Here's a link for some Good e-books on...

Here's a link for some Good e-books on electronics, their large.
http://openbookproject.net//electricCircuits/index.htm

For a voltage regulator you should search the web for "LM317"
Replies: 11
Views: 18,275
Posted By GWIZ

I have the steel set that I'm holding on too. ...

I have the steel set that I'm holding on too.
43764, 43765, 43766
Replies: 10
Views: 1,039
Posted By GWIZ

I'm not sure of what your talking about. The...

I'm not sure of what your talking about.

The under cuts are there because its difficult/costly to cut a 90 corner with a grinding wheel and guarantee your not going to have a fillet in the...
Replies: 18
Views: 29,722
Posted By GWIZ

"nap, gwiz; did you notice he stated it holds...

"nap,
gwiz; did you notice he stated it holds air when off? Not a bad check valve if it holds air. "

Yes,
I'm not sure what he is saying. its not holding air.
In his post # 3
He states, it...
Replies: 18
Views: 29,722
Posted By GWIZ

Sounds like your having problems with a one way...

Sounds like your having problems with a one way valve "Non return valve"
It prevents air from bleeding back into the pump or thru the valve that releases the head pressure so the pump can restart...
Replies: 11
Views: 4,602
Posted By GWIZ

The 6011 requires a higher voltage that most of...

The 6011 requires a higher voltage that most of the 110 volt machines don't put out.
tommyj3 is correct go with 6013 1/16" to 3/32" is about it.
If your using an extension cord, its needs to be...
03-06-07, 01:18 AM
Replies: 8
Views: 10,484
Posted By GWIZ

Some fluid masters, You may need to push down on...

Some fluid masters, You may need to push down on the float and submerge it, SOME had holes to allow water inside to counter balance the float.
If its the OLD style it needs to be submerged once to...
03-03-07, 02:07 AM
Replies: 11
Views: 15,593
Posted By GWIZ

There's too many variables in motor wiring. You...

There's too many variables in motor wiring. You need to take it to a motor shop.
t1 & t2 maybe a thermal overload.
t3 & t4 maybe a starting switch that is normally closed.
Or the other way around....
Replies: 11
Views: 11,472
Posted By GWIZ

The price of MIG wire is not that hi. you can buy...

The price of MIG wire is not that hi. you can buy 2 lbs spools every were for about $10.00
I don't advise buying larger rolls if your not doing a large project, they rust and give you feeding...
Replies: 5
Views: 1,167
Posted By GWIZ

A standard generator may not work for powering a...

A standard generator may not work for powering a TV.
I'm not up to date on the new TV's, But most synchronize the vertical with the 60 cycles from the power line which is very stable.
Most...
10-26-06, 10:24 AM
Replies: 27
Views: 9,765
Posted By GWIZ

Most of the amp clamps measure AC current only,...

Most of the amp clamps measure AC current only, If you have a little extra money you may look for one that will measure both AC and DC current.
DC amp clamp my help you check your charging system on...
08-27-06, 07:57 PM
Replies: 4
Views: 1,229
Posted By GWIZ

If you scroll down on that link, you will see a...

If you scroll down on that link, you will see a green square that you can down load the manual.
Then you can see the receptacle.
08-27-06, 04:28 PM
Replies: 4
Views: 1,229
Posted By GWIZ

I would try this. Router speed control. ...

I would try this.

Router speed control.

http://www.harborfreight.com/cpi/ctaf/displayitem.taf?Itemnumber=43060
08-26-06, 01:31 AM
Replies: 11
Views: 1,832
Posted By GWIZ

======== This statement is True if the power...

========
This statement is True if the power pack has a built in voltage regulator.
80 percent of the power packs don't have regulators, some-some items can be damaged by getting a higher current...
08-26-06, 12:21 AM
Replies: 8
Views: 1,077
Posted By GWIZ

Are your LED's made to operate on 12 volts ? ...

Are your LED's made to operate on 12 volts ?

Most, off the shelf LED's require an added resistor to operate from a specific voltage.
08-11-06, 01:33 AM
Replies: 6
Views: 991
Posted By GWIZ

frank, are you in the US ?

frank, are you in the US ?
08-09-06, 02:00 AM
Replies: 6
Views: 876
Posted By GWIZ

Hot. That's an indication of a bad connection...

Hot.
That's an indication of a bad connection or dirty contacts.
Best to replace the plug and receptacle and clean the wires before connecting them to the new parts.
08-06-06, 11:50 PM
Replies: 5
Views: 1,334
Posted By GWIZ

First reset the breakers, sometimes a tripped...

First reset the breakers, sometimes a tripped breaker will not show any indication of a trip.
If the breaker is powering a fridge or AC that's running wait 15 minutes before turning the breaker back...
08-06-06, 12:33 AM
Replies: 5
Views: 956
Posted By GWIZ

Yes. You may want to look at the link about...

Yes.

You may want to look at the link about Federal Pacific panels.
http://www.inspect-ny.com/fpe/fpepanel.htm
08-05-06, 02:31 PM
Replies: 20
Views: 91,043
Posted By GWIZ

nap beat me to the next question. I will add to...

nap beat me to the next question. I will add to it.

Can you list ALL the model and part numbers from the motor and lathe
And HF catalog numbers.
Name of lathe.
Does the lathe have a reverse...
08-04-06, 08:47 PM
Replies: 20
Views: 91,043
Posted By GWIZ

Is the motor AC or DC ? 120 volts or 90 volts,...

Is the motor AC or DC ?
120 volts or 90 volts, 24 volts. ?
08-01-06, 03:37 PM
Replies: 27
Views: 24,841
Posted By GWIZ

PM me with your E-mail address and I will send...

PM me with your E-mail address and I will send you a drawing using a DPDT switch that you can post for everyone to check for errors..
I will send a .Jpg drawing.
Showing results 1 to 25 of 200
 


 
Forum Jump