Search: Posts Made By: yanky
Showing results 1 to 13 of 13
Search took 0.01 seconds.
Replies: 30
Views: 7,703
Posted By yanky

Troop that is for the residential unit, I have...

Troop that is for the residential unit, I have the commercial unit that clearly states that I can use for space heating, it's somewhere in the manual right after where it mentions what you posted, I...
Replies: 30
Views: 7,703
Posted By yanky

hi guys here is the link on the rinnai site...

hi guys

here is the link on the rinnai site to my unit its the c98 commercial unit and says that it can be used for space heating but does not offer much info on it.

please let me know what you...
Replies: 30
Views: 7,703
Posted By yanky

Hi look at the picture the model # is...

Hi

look at the picture the model # is printed right on it there is no other info on it I was not the one who purchased it, I inherited this mess
Replies: 30
Views: 7,703
Posted By yanky

i mentioned before that either way i am going to...

i mentioned before that either way i am going to install a 3/4" flex or i will install rigid pipe that will conform to specs needed.

thanks for pointing it out.
Replies: 30
Views: 7,703
Posted By yanky

Hi As for the electric, i inherited this...

Hi

As for the electric, i inherited this mess and pretty much tried to redo the system and it was a complete mess much worse then my mess, as i said in the first post that the electrical wiring...
Replies: 30
Views: 7,703
Posted By yanky

i just have boiler drains at the end of the...

i just have boiler drains at the end of the manifold no loop.

do you think if i just add the straight extensions to the runs of the close tees as described in drawing #6 and moved the pump to the...
Replies: 30
Views: 7,703
Posted By yanky

primary loop close tee problem

thanks trooper, as i said i am new at this and i am actually terrible at puzzles, now i got what you guys are saying, so i must switch the tees around to make it work properly? the way the tees are...
Replies: 30
Views: 7,703
Posted By yanky

I know I have to change the flex but I don't...

I know I have to change the flex but I don't think that is an issue, because the unit is running well and heating the water to 185 degrees instantly and no matter what flow rate I put thru it...
Replies: 30
Views: 7,703
Posted By yanky

so you say move the pump right on to the return?...

so you say move the pump right on to the return? i am a bit lost on what you are saying about the secondary loop isn't that what i have coming out of the tees.

the boiler a rinnai c98 237,000 btu...
Replies: 30
Views: 7,703
Posted By yanky

Boiler set up, Primary Secondary problem (pictures in post)

Hi to all

I am new and just put this system together, a first for me.

what i have is an 8 zone cast iron baseboard system being fed by 3/4" pex
with a tankless boiler,

problem is water in...
Replies: 4
Views: 2,225
Posted By yanky

Thanks Rock what you and TOH are saying sounds...

Thanks Rock what you and TOH are saying sounds good to me.
Replies: 4
Views: 2,225
Posted By yanky

Hi Thanks for the response, I agree with you...

Hi
Thanks for the response, I agree with you about the boiler, its just that it was left over from a job.

As for replaceing the 8 pumps i have about 600 feet of 3/4 pipe feeding the zones, do you...
Replies: 4
Views: 2,225
Posted By yanky

Installing a Nortitz Tankless Boiler on 8 zone hydronic baseboard, please advise

Hi i am new to this group so please go easy on me.

I am planning on installing this system as drawn, it is an 8 zone hot water baseboard with primary secondary.

Please feel free to advise if...
Showing results 1 to 13 of 13


 
Forum Jump