Search: Posts Made By: joe384
Showing results 1 to 22 of 22
Search took 0.01 seconds.
Replies: 6
Views: 668
Posted By joe384

I ordered a new motor and installed it yesterday....

I ordered a new motor and installed it yesterday. All is well. It's running like new. Thanks for the help!
Replies: 6
Views: 668
Posted By joe384

There is a wire going to the switch box that...

There is a wire going to the switch box that looks more purple than blue, but I'm assuming that is the blue one. There is no power between the blue and yellow wires to the switch box.
...
Replies: 6
Views: 668
Posted By joe384

Thanks for the reply! When I put power on...

Thanks for the reply!

When I put power on the motor to check the yellow and blue wires, and the motor starts humming, will the motor be damaged if I leave power on it too long? If so, how long is...
Replies: 6
Views: 668
Posted By joe384

Maytag washer LAT4916AAE motor hums, does not start

My Maytag LAT4916AAE fills with water, but does not agitate or spin, and the motor makes a loud humming noise.

I removed both belts, and the pump pulley rotates freely. The brake pulley also turns...
Replies: 10
Views: 742
Posted By joe384

The problem was the tub bearing. It was almost...

The problem was the tub bearing. It was almost completely seized. I installed a tub bearing kit, and a mounting stem repair kit. The machine is running like new.
Replies: 10
Views: 742
Posted By joe384

It looks to me like there is a lot of grease...

It looks to me like there is a lot of grease under the grease cap.
Replies: 10
Views: 742
Posted By joe384

When I turn the pulley in the spin direction the...

When I turn the pulley in the spin direction the transmission does not lift at all.
Replies: 10
Views: 742
Posted By joe384

I replaced the clutch brake assembly and still...

I replaced the clutch brake assembly and still have the same symptoms. Agitate works, but spin doesn't. It appears that something is causing the spin drum to lock up. It isn't locked up completely,...
Replies: 10
Views: 742
Posted By joe384

Thanks for the reply! When you say you never...

Thanks for the reply!

When you say you never used the special tool, do you mean there is another method to remove and replace the brake assembly? I saw one forum post that said a chain visegrip...
Replies: 10
Views: 742
Posted By joe384

Maytag Washer LAT4916AAE not spinning, belt smell

The washer fills, agitates, and drains just fine. The motor and lid switch are working. New belts, motor springs, and glides.

With the belts removed, I can turn the pully in the agitate direction...
Replies: 1
Views: 501
Posted By joe384

Solution

I managed to figure this out on my own.

I did some more googling and found a forum post about a similar problem, but with a different refrigerator. The suggested solution was to remove the screw,...
Replies: 1
Views: 501
Posted By joe384

GE Profile refrigerator evaporator access

I can't figure out how to get the evaporator cover off in my GE Profile PDS18SBMBRBS refrigerator. The freezer is at the bottom.

Here is a parts list:
Parts for GE PDS18SBMBRBS: Cabinet Parts -...
Replies: 25
Views: 7,651
Posted By joe384

Thanks, Grady. Would you use pipe dope, or teflon...

Thanks, Grady. Would you use pipe dope, or teflon tape?
Replies: 25
Views: 7,651
Posted By joe384

I installed the new tankless coil a few weeks...

I installed the new tankless coil a few weeks ago. The new tankless coil came with steel studs and brass nuts. I torqued the nuts gradually to 20 ft-lb over a period of about two weeks.

Now it's...
Replies: 25
Views: 7,651
Posted By joe384

Thanks, Grady. Is it Permatex 81878? Permatex...

Thanks, Grady. Is it Permatex 81878?
Permatex 81878 | Liquid Gasketing & Silicone Sealants (http://www.all-spec.com/products/81878.html)
Replies: 25
Views: 7,651
Posted By joe384

I'm ready to install the new tankless coil. It...

I'm ready to install the new tankless coil. It came with a rubber gasket. No instructions were included. Should I put any kind of sealant on the gasket? I thought a saw a forum posting somewhere that...
Replies: 4
Views: 5,408
Posted By joe384

Do you think part number 7353T23 on this web page...

Do you think part number 7353T23 on this web page McMaster-Carr (http://www.mcmaster.com/#7353t23/=d0mcuf) would do the job? The brush diameter is 1/2", brush length 3", and the overall length is...
Replies: 4
Views: 5,408
Posted By joe384

Brushes for Furnace Cleaning

My oil furnace is a Weil McLain P-368-WT. I looked on the McMaster-Carr website for brushes to clean it with, and was overwhelmed by all the choices. Can anyone suggest a set of brushes to use for...
Replies: 25
Views: 7,651
Posted By joe384

Great information! Thanks to everyone!

Great information! Thanks to everyone!
Replies: 25
Views: 7,651
Posted By joe384

Would Permatex 80078 Anti-Seize Lubricant be...

Would Permatex 80078 Anti-Seize Lubricant be okay?

I'm nervous about using the existing 3/8-16 holes because I'm afraid the bolts might not hold well. Is it hard to drill and and tap bolt holes in...
Replies: 25
Views: 7,651
Posted By joe384

Thanks. Advice (spelled correctly this time)...

Thanks. Advice (spelled correctly this time) appreciated!

How much torque should be applied when tightening the bolts?
Replies: 25
Views: 7,651
Posted By joe384

Tankless Coil - Broken Bolts

While removing the tankless coil from my Weil-McLain B-68 boiler, five of the six bolts broke off. The boiler was installed in 1988. The bolts are 3/8-16 3/4". I will need to drill out the bolts and...
Showing results 1 to 22 of 22


 
Forum Jump