Search: Posts Made By: kolias
Showing results 1 to 25 of 43
Search took 0.01 seconds.
Replies: 9
Views: 260
Posted By Fred_C_Dobbs

"Cant create directory on C:\." Does that...

"Cant create directory on C:\."

Does that mean you were trying to install something in the root directory, or was the complete message something like, "Can't create directory on C:\Program Files"?...
Replies: 7
Views: 266
Posted By Hal_S

Hit the Windows-key, then type "task" which will...

Hit the Windows-key, then type "task" which will give you to option to start "Task Manager." Select the option to run as administrator.
First, check the list of applications which are enabled at...
Replies: 18
Views: 672
Posted By Pilot Dane

In post #5 a MIG welder is being used.

In post #5 a MIG welder is being used.
Replies: 18
Views: 672
Posted By XSleeper

Plumbing solder is probably way too soft, and has...

Plumbing solder is probably way too soft, and has too low of a melting point. You likely want a bronze alloy.

What you want to do is called brazing. Not welding. And you want the thinnest flux...
Replies: 4
Views: 144
Posted By XSleeper

Your inside cutout you go clockwise, your outer...

Your inside cutout you go clockwise, your outer cut will be counterclockwise. Look at the direction your bit turns. You always want the cutting side of the bit to be cutting into the material you...
Replies: 16
Views: 601
Posted By philmb79

Hey mate. I bought one of these for my...

Hey mate.
I bought one of these for my Millwaukee rotary tool (Same thing as a Dremel)
https://www.dremel.com.au/au/en/dremel%C2%AEezlocksandingmandrel-sandingband-742-ocs-p/
It works like a...
Replies: 16
Views: 601
Posted By SandburRanch

Try using a little force to the rubber drum by...

Try using a little force to the rubber drum by rolling it between 2 pieces of lumber then putting it in the freezer to shrink slightly while the sanding sleeve is warming to around 120įF with a hair...
Replies: 3
Views: 209
Posted By marksr

So there is no jamb or room for a jamb?

So there is no jamb or room for a jamb?
Replies: 3
Views: 209
Posted By Pilot Dane

You will have to mount the hinges on the surface...

You will have to mount the hinges on the surface of the steel frame as mortising is quite difficult, so the gap on the hinge side will be slightly larger than normal. But, a little drilling and...
Replies: 2
Views: 156
Posted By CircuitBreaker

I use the tool Keepvid.pro and it almost always...

I use the tool Keepvid.pro and it almost always works (if it does not keep trying as they probably want you to buy the paid version)

Try This (https://keepvid.pro/en/youtube/kPguktA674w) Link here...
Replies: 6
Views: 300
Posted By CircuitBreaker

I also vote DC as the one with Red/Black wires...

I also vote DC as the one with Red/Black wires the red one has a red dot meaning the positive pole of the DC circuit what voltage I have no idea. Most printers use 32 VDC (at least the ones having...
Replies: 6
Views: 300
Posted By Bob14525

While I can't say for certain, I would be willing...

While I can't say for certain, I would be willing to bet that the motors are DC. Almost all printers use DC voltage to run the electronics and motors. As for voltage, I would guess 12VDC maximum. ...
09-10-20, 09:03 AM
Replies: 7
Views: 350
Posted By Pilot Dane

I've made Rube Goldberg rolling ball machines...

I've made Rube Goldberg rolling ball machines with everything from BB size ball bearings up to pinballs. Use what you've got. I will say that it gets harder as the balls get smaller because it...
08-31-20, 05:37 PM
Replies: 10
Views: 312
Posted By pcboss

250 watts per foot was a common size. For example...

250 watts per foot was a common size. For example a 6 foot heater would be 1500 watts.
08-31-20, 10:00 AM
Replies: 10
Views: 312
Posted By joed

What is the amperage of the circuit the heaters...

What is the amperage of the circuit the heaters are on?
08-31-20, 06:05 AM
Replies: 10
Views: 312
Posted By Pilot Dane

Length doesn't tell you the power of a electric...

Length doesn't tell you the power of a electric baseboard heater. Older heaters had almost twice the wattage for their size but they got hot enough to melt plastics and possible cause a fire if...
Replies: 6
Views: 402
Posted By aandpdan

The easiest way would probably be for you to...

The easiest way would probably be for you to import the picture(s) into a Word document and then save that file, password protected.
Replies: 21
Views: 450
Posted By Pilot Dane

I have installed a few vent caps. On the ground...

I have installed a few vent caps. On the ground I glue together a couple 90 degree fittings to make a 180. I cover the open end with hardware cloth. Then attach it to the top of the vent stack on...
Replies: 21
Views: 450
Posted By Zorfdt

If it's been 6-8 years since your last clog, a...

If it's been 6-8 years since your last clog, a good snaking could give it another 6-8 years, I'd probably just do that.

Another option would be to run a camera snake down the pipe. There may be a...
Replies: 21
Views: 450
Posted By Pilot Dane

If you go several hours without using any water...

If you go several hours without using any water in the house. Then run water in the sink. How long it takes to back up can give you an idea how far away the clog is located. If it backs up right...
05-17-20, 08:20 AM
Replies: 5
Views: 426
Posted By 2john02458

Thinning the wood filler with a little water...

Thinning the wood filler with a little water helps it to get absorbed and stick to the plywood edge better.
05-17-20, 06:20 AM
Replies: 5
Views: 426
Posted By marksr

Most any wood filler could be use to fill the...

Most any wood filler could be use to fill the edge of the plywood if you are going to paint it.
Replies: 6
Views: 423
Posted By GregH

In some cases there is a consideration when...

In some cases there is a consideration when determining pulley spacing.
Yow want them separated to maximize belt to pulley contact on the smaller pulley but not too far apart to prevent belt slap....
Replies: 6
Views: 423
Posted By joecaption

V-Belt Length Calculator...

V-Belt Length Calculator (http://www.calculatoredge.com/mech/vbelt%20length.htm)
Replies: 6
Views: 423
Posted By Zorfdt

Nope, no difference regarding distance. The only...

Nope, no difference regarding distance. The only speed/torque determination is the size of the two pulleys.
Showing results 1 to 25 of 43
 


 
Forum Jump