Search: Posts Made By: Dean Miller
Showing results 1 to 20 of 20
Search took 0.01 seconds.
06-01-15, 12:08 AM
Replies: 2
Views: 899
Posted By Dean Miller

Increase Pipe Feeding softener

I have a softener fed via a 3/4" supply from a pressure tank and I still get some rust on my fittings. I was thinking off adding sediment filter post softener. There is a 1" line from well to the...
04-02-14, 06:55 AM
Replies: 11
Views: 1,125
Posted By Dean Miller

Thank you for everyone's help. All I need to do...

Thank you for everyone's help. All I need to do is purchase the length of 6-3 wire and get someone to install the inlet on the side of the house. Don't want to screw up the siding. I'm confidant...
03-26-14, 05:20 PM
Replies: 11
Views: 1,125
Posted By Dean Miller

I stand corrected again. So what size of cable...

I stand corrected again. So what size of cable do I need to connect the power inlet to the transfer panel. Connecting the transfer panel to the circuits I want to power off the generator is easy...
03-26-14, 04:00 PM
Replies: 11
Views: 1,125
Posted By Dean Miller

I stand corrected. Yes, the power inlet.:)

I stand corrected. Yes, the power inlet.:)
03-25-14, 11:09 PM
Replies: 11
Views: 1,125
Posted By Dean Miller

I ordered the cable to connect to the house from...

I ordered the cable to connect to the house from the generator already made up. I need to check the requirements for wire size between the Reliance panel and the plug on the outside of the house....
03-24-14, 07:45 PM
Replies: 11
Views: 1,125
Posted By Dean Miller

I plan on using a Reliance 50 amp manual transfer...

I plan on using a Reliance 50 amp manual transfer switch (10 circuits) with a 50 amp plug. I think I need (6-2 w/ground) wire to run from the plug to the switch. With the same size wire going from...
03-21-14, 10:47 AM
Replies: 11
Views: 1,125
Posted By Dean Miller

Question New Generator questions

I purchased a 8000 Watt with a 10000 Watt surge generator from Powerland and I want to connect it to a manual transfer switch in the basement. I plan on utilizing the 120/240 50 amp outlet to supply...
12-02-13, 07:55 PM
Replies: 3
Views: 2,049
Posted By Dean Miller

It looks like all the piping up to the water...

It looks like all the piping up to the water heater is 3/4 inch with the split off to the devices 1/2".
12-02-13, 07:05 PM
Replies: 3
Views: 2,049
Posted By Dean Miller

Question Piping size from pressure tank to softener and to house

I have a 1" line from my well to the pressure tank on one side of the tank tee. The tank is 44 gal with a 30/50 pressure switch and the bladder is set to 28 psi. I have a 1" line going back out to a...
10-22-13, 12:41 AM
Replies: 2
Views: 4,239
Posted By Dean Miller

Question Century, Bryant or Concord Furnace 2-stage vs variable speed

Hello everyone. I am pricing a new furnace for a 2832 sq ft house. It was built in 2008. The furnace was damaged in a flood prior to my purchase of the home and it was a Bryant Plus 90t. I am...
Replies: 2
Views: 795
Posted By Dean Miller

Alarm System

I'm looking for an alarm system that has door/window monitoring with keypad and local alarm but not monitored remotely. It needs to be able to announce when a door is open. Basically a local alarm...
10-19-13, 06:03 PM
Replies: 8
Views: 989
Posted By Dean Miller

My well, dryer, and AC compressor. I'd think...

My well, dryer, and AC compressor. I'd think would be the biggest draw. Maybe the furnace motor not sure. Other then that I don't think the load would be that great.
10-18-13, 06:00 PM
Replies: 8
Views: 989
Posted By Dean Miller

Generator for House

I'm thinking of buying a generator for the house I am buying. Any suggestions on how to size the unit and other manufactures to look at. I went to Generac's web site and for my size of home and...
10-18-13, 05:54 PM
Replies: 2
Views: 742
Posted By Dean Miller

Electrical Panel had 4 breakers under water.

Hi. I am purchasing a HUD home that had a flooded basement. Of course the 42 switch panel and a smaller 24(I think) panel had gotten wet up to the 3rd breaker from the bottom. HUD has the panel on so...
Replies: 4
Views: 696
Posted By Dean Miller

Pilot Dane, I need to cap lines in the kitchen...

Pilot Dane, I need to cap lines in the kitchen where the PO removed all the cabinets but then I think I can pressurized the lines.
10-18-13, 05:18 PM
Replies: 10
Views: 1,775
Posted By Dean Miller

Chandler, not sure how long it was that deep. It...

Chandler, not sure how long it was that deep. It only had an 1" of water when I looked at it. I'm guessing it the fittings that are bonded to help get rid of any static that may develop. I'm going to...
Replies: 4
Views: 696
Posted By Dean Miller

Yes, I am talking about the submersible pump. I...

Yes, I am talking about the submersible pump. I had though along the same lines. Hook it up and see if it runs. Any correct steps on getting it back in service as far as the pressure tank goes?
10-17-13, 05:09 PM
Replies: 10
Views: 1,775
Posted By Dean Miller

Hopefully this works for a photo. The pipe is...

Hopefully this works for a photo. The pipe is plastic. A contractor today told me it is OK to use but it has to be bonded to the ground on the panel. This is different and I think I may change it...
10-17-13, 10:20 AM
Replies: 10
Views: 1,775
Posted By Dean Miller

Question Plastic gas piping

Does anyone know if plastic piping is allowed for natural gas lines. I live in Ohio and purchasing a HUD home that I will need to replace the furnace and hot water tank. I noticed that the gas line...
Replies: 4
Views: 696
Posted By Dean Miller

Question Well Question

I am purchasing a home that had water in the basement (4 ft initially). I need to replace the pump controls and maybe the pressure tank. The tank is questionable because it was under water but does...
Showing results 1 to 20 of 20


 
Forum Jump