Go Back  DoItYourself.com Community Forums > Search Forums
Reload this Page >

Search Results

Search: Posts Made By: Utterly-NutZ
Showing results 1 to 16 of 16
Search took 0.01 seconds.
Forum: Ducting, Air Circulation and Ventilation Systems
11-03-19, 12:18 PM
Replies: 3
Views: 230
Posted By Utterly-NutZ

For mine to flash a code, I needed it to fail 3...

For mine to flash a code, I needed it to fail 3 or 4 times to make it go into lockout, then the light on the board would give me a code (ignition failure). In my case, it was not getting 120v to the...
Forum: Gas and Oil Home Heating Furnaces
10-28-19, 02:50 PM
Replies: 2
Views: 515
Posted By Utterly-NutZ

I'm certainly no expert, but have you checked...

I'm certainly no expert, but have you checked and/or cleaned the flame sensor?
I keep a piece of scrub pad (plain, no soap!) by the furnace and check it/give it a few swipes and put it back when I...
Forum: Ducting, Air Circulation and Ventilation Systems
10-20-19, 04:28 AM
Replies: 23
Views: 790
Posted By Utterly-NutZ

I highly recommend cats, but that's just me. ...

I highly recommend cats, but that's just me.

I have city cats, they just corner the mice and I rescue and release. We've only had 3 in the 10 years I've lived in this house (thankfully)

Before...
Forum: Computers, Internet Capable Devices and Peripherals
10-18-19, 02:45 PM
Replies: 13
Views: 786
Posted By Utterly-NutZ

If you live in a busy neighbourhood, and the...

If you live in a busy neighbourhood, and the router is using defaults, then it might be the channel that you are using. The usual suspects are channel 1, 6 & 11; you may want to change that if you...
Forum: Electrical - AC & DC
10-14-19, 06:30 AM
Replies: 4
Views: 312
Posted By Utterly-NutZ

I was today years old when I learned what those...

I was today years old when I learned what those outlets were for lol
Forum: Gas and Oil Home Heating Furnaces
10-08-19, 10:36 AM
Replies: 8
Views: 529
Posted By Utterly-NutZ

And finally - my follow up. New board arrived...

And finally - my follow up.
New board arrived (Nordyne 903106) - (Old one was ICM AA1011-4 or Nordyne part 6245640)

Board installed and voila! issue resolved

Extra huge thanks to PJmax for the...
Forum: Computers, Internet Capable Devices and Peripherals
10-07-19, 03:42 PM
Replies: 20
Views: 830
Posted By Utterly-NutZ

This is a common thing to happen with the HP...

This is a common thing to happen with the HP Pavilions, not sure why.

Have you tried either of the following:
Unplug the power cable from the computer, hold down the power button for 5 seconds,...
Forum: Toilets, Sinks, Showers, Dishwashers, Tubs and Garbage Disposals
09-28-19, 12:29 PM
Replies: 12
Views: 398
Posted By Utterly-NutZ

I absolutely agree with everyone about switching....

I absolutely agree with everyone about switching. I have also gone with the 400a series in both of the toilets in my house, and very happy I did.
Forum: Indoor and Outdoor Animal Control
09-27-19, 03:59 PM
Replies: 12
Views: 793
Posted By Utterly-NutZ

Cute, but not in the house It's a tad hard...

Cute, but not in the house

It's a tad hard to tell in the pictures, but the markings look like they are 'blotches' so based on that, looks like you have a common garter snake. Non-venomous, yes,...
Forum: Toilets, Sinks, Showers, Dishwashers, Tubs and Garbage Disposals
09-27-19, 03:53 PM
Replies: 12
Views: 398
Posted By Utterly-NutZ

If it's a float arm with a ball, you should be...

If it's a float arm with a ball, you should be able to get the exact same item (or near the same) from the hardware store.

That said, I did have one of my toilets where the crack was actually the...
Forum: Toilets, Sinks, Showers, Dishwashers, Tubs and Garbage Disposals
09-27-19, 03:04 PM
Replies: 12
Views: 398
Posted By Utterly-NutZ

Make sure the float isn't rubbing against the...

Make sure the float isn't rubbing against the sides of the tank, or obstructed in some way. You can also get away with bending the float arm slightly as long as it's not made of plastic that could...
Forum: Gas and Oil Home Heating Furnaces
09-26-19, 04:11 AM
Replies: 8
Views: 529
Posted By Utterly-NutZ

I suspected that but figured it wouldn't hurt to...

I suspected that but figured it wouldn't hurt to start with the less expensive part. I greatly appreciate your time on this.
I will be putting an order in for the board and will update this thread...
Forum: Gas and Oil Home Heating Furnaces
09-25-19, 04:58 PM
Replies: 8
Views: 529
Posted By Utterly-NutZ

Gave that a shot (hope I did it all correctly)...

Gave that a shot (hope I did it all correctly) and where the click happens that I would expect the HSI to glow, I get a quick burst of about 80v and then it drops back to the 00.3 to 6 showing on the...
Forum: Gas and Oil Home Heating Furnaces
09-25-19, 04:12 AM
Replies: 8
Views: 529
Posted By Utterly-NutZ

Thank you for the reply. Do I test the molex plug...

Thank you for the reply. Do I test the molex plug with the power on and an attempt at a cycle run? Is this the only time 120 volts will be sent to the HSI or is that voltage always present?
Forum: Computers, Internet Capable Devices and Peripherals
09-24-19, 05:39 PM
Replies: 1
Views: 551
Posted By Utterly-NutZ

I believe the start and volume options will only...

I believe the start and volume options will only work on the Android tablets. Can you try to do the following:

Start your tablet, and just as Windows attempts to load (spinning dots), press and...
Forum: Gas and Oil Home Heating Furnaces
09-24-19, 05:21 PM
Replies: 8
Views: 529
Posted By Utterly-NutZ

Unhappy Furnace Clicks but does not light

Hello Everyone!

After a few weeks of searching, and more searching, I landed on this forum and and hoping for some help. To start with, I'm not opposed to calling a professional, but I would very...
Showing results 1 to 16 of 16


 
Forum Jump

Do Not Sell My Personal Information