Search: Posts Made By: pslatin
Showing results 1 to 25 of 49
Search took 0.01 seconds.
Replies: 5
Views: 233
Posted By pslatin

Thank you Ron and WW. I advised the owner of her...

Thank you Ron and WW. I advised the owner of her options and she has been thinking about it. I am betting if she called ADT they would give her a good deal on a new panel as long as she signed some...
Replies: 5
Views: 233
Posted By pslatin

Adt scw9057g-433

I am trying to help someone with an ADT scw9057g-433 alarm system in their new condo. Owner is asking me if there is a way to connect this to the internet so that she can monitor and/or control it...
Replies: 28
Views: 1,278
Posted By pslatin

Thanks Ron. The manual provided in your link is...

Thanks Ron. The manual provided in your link is very good -- better than the one that came with the PC1832 board.

I set both PGM's to "03" Sensor Reset in Section [009] and the system went into...
Replies: 28
Views: 1,278
Posted By pslatin

Continued thanks. Still concerned about...

Continued thanks.

Still concerned about Section [009]. Recall I have a black wire connected to PGM-1 on the board and have Fire on Zone 1. I am sitting on the defaults for [009] of "19" for...
Replies: 3
Views: 639
Posted By pslatin

Thanks Ron. When I defaulted the system (the...

Thanks Ron.

When I defaulted the system (the procedure jumping I/O 1 and 2 etc) ... it cleared the armed state and the master code returned to 1234 ... it looks like it worked ... but I cannot get...
Replies: 28
Views: 1,278
Posted By pslatin

Thank you Ron. Did you mean PGM 2? I...

Thank you Ron.

Did you mean PGM 2? I checked the panel and there is a black wired connected to PGM 1 ... and if you look at the pic below of the old panel (that was replaced), that same black...
Replies: 28
Views: 1,278
Posted By pslatin

Is there a prize for longest DIY project ever...

Is there a prize for longest DIY project ever here?

This project is finally wrapping up. The replacement PC1832NK board has been swapped in and the system is up and running. I have reprogrammed...
Replies: 3
Views: 639
Posted By pslatin

Adt scw9057g-433

My daughter recently bought a condo with this system installed. It has 3 door sensors, 1 window sensor, and 1 motion sensor. We did not get the master code or the installer code from the seller and...
05-19-20, 11:48 AM
Replies: 12
Views: 364
Posted By pslatin

Whole House Pressure Control & Monitoring

Thank you everyone.

So the pressure gauge on the Caleffi is measuring the downstream "reduced" pressure ... so if I want to see what's coming in from the city, I need to add one after the meter...
05-18-20, 01:56 PM
Replies: 12
Views: 364
Posted By pslatin

Pressure Reducing Valve

Well since I started this chain back in January we've been through a virus and the world has changed. I saw a post asking about quarantine projects so I better dust this one off and get on with it.
...
Replies: 28
Views: 1,278
Posted By pslatin

Envisalink 4

Thanks Ron. Sigh. This sounds like a huge job. I am attaching a couple of pics to share what I am looking at.

At this point I am wondering how to proceed.

Is it possible to carefully move all...
Replies: 28
Views: 1,278
Posted By pslatin

Well 24 hours has come and gone and still showing...

Well 24 hours has come and gone and still showing a yellow trouble for BATTERY.

I checked the voltage at the battery terminals and I am seeing 12.5V. I just powered everything down and am going...
Replies: 28
Views: 1,278
Posted By pslatin

UPDATE: So I cycled the power and it cleared all...

UPDATE: So I cycled the power and it cleared all the faults except for a LOW BATTERY fault. I ordered a new ELK battery which came yesterday and I just installed it today. Also recycled power and...
Replies: 28
Views: 1,278
Posted By pslatin

Hello: So all seems to be working well but I...

Hello:

So all seems to be working well but I am still showing the trouble light with the code "Communications". I made the changes to sections 015, 371, and 380 according to my last post but I am...
Replies: 28
Views: 1,278
Posted By pslatin

It was sort of obvious that I wanted to connect...

It was sort of obvious that I wanted to connect to the RED-BLK-YEL-GRN and I did and it seems to be working.

I am now seeing some phone line trouble codes. So I assume I need to do this?
...
Replies: 28
Views: 1,278
Posted By pslatin

Thank you Ron. There are two 4-strand cables...

Thank you Ron.

There are two 4-strand cables running to the Escort 5580TC. I am assuming I can use one of these to connect to the EVL-4EZR -- but wondering which one? Can I leave the other one...
Replies: 28
Views: 1,278
Posted By pslatin

Hi Ron (others): I am about to start...

Hi Ron (others):

I am about to start installing the EVL-4. First I want to remove the Escort 5580TC. Besides disconnecting it (I believe there are 4 wires to the main 5010 panel) ... do I have...
03-07-20, 03:33 PM
Replies: 13
Views: 1,372
Posted By pslatin

6202 / ecobee 4

Yes I used the PEK. You need to if you do not have five wires to the stat. I donít know about the ecobee 3 lite as I have ecobee 4 ... but I donít think there is a difference in wiring. No I only...
02-12-20, 11:57 AM
Replies: 13
Views: 1,372
Posted By pslatin

UPDATE: So I wonder if somewhere in these forums...

UPDATE: So I wonder if somewhere in these forums there is a place for DIY'ers who make bonehead moves. Is there a Hall of Fame or Hall of Shame somewhere? I am a 2020 candidate.

So ... as long...
02-11-20, 01:16 PM
Replies: 13
Views: 1,372
Posted By pslatin

Update: I talked to Aprilaire and one of their...

Update: I talked to Aprilaire and one of their concerns was that maybe the zone board was underpowered and not getting the full 24V to the ecobee 4. I did validate that the transformer for the zone...
02-09-20, 02:42 PM
Replies: 13
Views: 1,372
Posted By pslatin

Thank you again PJ. I tried to check the voltage...

Thank you again PJ. I tried to check the voltage across X and R ... and I blew a fuse on the unit.

At this point I am going to sleep on it and try tomorrow to make sense of this. I might call...
02-09-20, 11:31 AM
Replies: 13
Views: 1,372
Posted By pslatin

Yes it is surprising that there isn't more on the...

Yes it is surprising that there isn't more on the internet regarding this board.

I tried the X terminal but could not get that to work as well. If I use my multimeter to check, I want to put...
02-08-20, 10:19 PM
Replies: 13
Views: 1,372
Posted By pslatin

Aprilaire 6202

PJ -- Thank you for your response.

Yes! Nothing I can find online matches what I have installed here at home. See pics and let me know what you think.
02-08-20, 05:20 PM
Replies: 13
Views: 1,372
Posted By pslatin

Installing ecobee 4 with Aprilaire 6202 Zone Control

I spent several hours trying to get this to work with ecobee support to no avail. I am trying to use the ecobee 4 PEK since I only have 4 wires between the 6202 and the stat. The main issue is that...
01-12-20, 05:26 PM
Replies: 12
Views: 364
Posted By pslatin

Thanks. Yes I think I need a PRV. At a minimum...

Thanks. Yes I think I need a PRV. At a minimum I am fine with that, but am wondering if there are any recommendations for fancier gadgets, etc.
Showing results 1 to 25 of 49
 


 
Forum Jump