Search: Posts Made By: Racerx143
Showing results 1 to 20 of 20
Search took 0.01 seconds.
Replies: 4
Views: 175
Posted By Racerx143

"Do any lights blink after it pauses ?" No, ...

"Do any lights blink after it pauses ?"

No, They just stay lite as if the unit is still working. Last night I ran it and it paused again with the soap lid open and the pod just sitting in the...
Replies: 4
Views: 175
Posted By Racerx143

I thought they just stay lit. Just to be sure,...

I thought they just stay lit. Just to be sure, I'm going to run it again and make sure. Thanks.
Replies: 4
Views: 175
Posted By Racerx143

Dishwasher stopping after rinse cycle

I need help with a Whirlpool dishwasher model WDF540PADW1. I’ve had it about 5 or 6 years. It stops during use at the same point. When I hit start I can hear it filling and then running...
11-12-20, 10:57 AM
Replies: 5
Views: 332
Posted By Racerx143

Thanks for the replies. I just wanted something...

Thanks for the replies. I just wanted something on hand that would work in a pinch. The SAE kit O-rings always seem to be too thick. I don't recall ever actually using it and I have had it for...
11-10-20, 07:38 PM
Replies: 5
Views: 332
Posted By Racerx143

Metric O-Ring kit

I currently own a SAE O-ring kit which never seems to fit anything I need it for. It's one of those red case cheapies you can pick up almost anywhere. What I never realized up until recently was...
Replies: 13
Views: 1,316
Posted By Racerx143

(Thanks PJmax) Got it running. There were...

(Thanks PJmax)
Got it running. There were multiple issues which I discovered one right after the other. The plug appeared to be fine, even tested ok with multimeter. I went ahead and put a...
Replies: 13
Views: 1,316
Posted By Racerx143

I have 3 plugs and they all do the same exact...

I have 3 plugs and they all do the same exact thing.

Yes, the timing uses an inductive clamp.

I have been grounding to the cylinder head.
Replies: 13
Views: 1,316
Posted By Racerx143

Spark outside of engine, none/sporadic while installed

I have another thread going here regarding a scooter I cant get to run. I have run into a general question that I have never experienced before.

I have been trying to get this scooter to run...
Replies: 13
Views: 1,316
Posted By Racerx143

The DC CDI is about twice the size of the AC CDI....

The DC CDI is about twice the size of the AC CDI. I did a complete electronic test on every component and I know this engine is powered by the magneto. One of the test is to check for AC power to...
Replies: 11
Views: 2,093
Posted By Racerx143

Dont know if you have figured this out yet or not...

Dont know if you have figured this out yet or not but I have pipes I melt my shoes on from time to time. What works for me is to warm the pipes up. I use a chrome polish little Mothers that also is...
Replies: 13
Views: 1,316
Posted By Racerx143

I should receive my tool tomorrow or Friday to...

I should receive my tool tomorrow or Friday to pull the rotor. I feel this is a timing issue. I have everything needed for it to run; spark, compression and fuel yet it wont.
Replies: 13
Views: 1,316
Posted By Racerx143

The flywheel key looks ok.. I can see it in its...

The flywheel key looks ok.. I can see it in its slot on the shaft and in the slot on the rotor. When I line the TDC mark up on the rotor the cam is lined up where it should be and the engine is at...
Replies: 13
Views: 1,316
Posted By Racerx143

Thanks for reply I just noticed this is probaby...

Thanks for reply I just noticed this is probaby in the wrong section and I am trying to delete or have it moved to the motorcycle section.
Replies: 13
Views: 1,316
Posted By Racerx143

150cc Chinese Scooter Will not run. Has spark, fuel and compression

Working on a friendís 150cc Chinese scooter (GY6 seems to be the common term) Problem is it will not start. This engine uses a CDI, Coil, Stator/Rotor set up for spark, very simple. Checked spark...
05-17-18, 08:52 AM
Replies: 1
Views: 640
Posted By Racerx143

Compressor quick connect wire ends.

Just had an issue where the start wire melted off of the spade at the compressor. This issue has been fixed but I had to rig up a wire from the cap to the compressor because I don't have a female...
11-03-06, 03:02 PM
Replies: 5
Views: 8,658
Posted By Racerx143

the blfc button is there, i remember putting it...

the blfc button is there, i remember putting it back in. but had one of those opps moments today that turned out to be the fix... i was taking things apart one last time and accidently blow the...
11-03-06, 07:43 AM
Replies: 8
Views: 5,129
Posted By Racerx143

JustALurker mentioned: (Also check that the...

JustALurker mentioned: (Also check that the locating pin (nub) is holding the motor. If that pin/nub breaks off the motor can turn and that would stall regeneration an that point)

If the motor is...
11-03-06, 07:26 AM
Replies: 5
Views: 8,658
Posted By Racerx143

All of the connections are solid, no leaks. ...

All of the connections are solid, no leaks. lines are good (hard type not pinched). float works. you mentioned a BLFC (brine line flow control). Not sure what that is. the thing that baffles me,...
11-02-06, 05:15 PM
Replies: 5
Views: 8,658
Posted By Racerx143

Fleck 5600 will not draw brine

Iíve searched a ton of posts here and canít seem to find anything to help with my problem. I can cycle the knob thru all the cycles and everything seems to work except the drawing of brine out of...
Showing results 1 to 20 of 20


 
Forum Jump