Search: Posts Made By: Jrothwell
Showing results 1 to 25 of 59
Search took 0.01 seconds.
Replies: 1
Views: 134
Posted By Jrothwell

Vista32fb zone response time

Hello,

I have a micro switch that Iím trying to use to activate a fire zone. Itís attached to a Masterbox hook and creates a short for approximately 1 second or a little less. This does not...
Replies: 2
Views: 256
Posted By Jrothwell

Honeywell LTE Antenna Type

Hello,

I have a Honeywell CELL-XA LTE communicator. Am I able to use the GS15-ANT http://181.164.114.46/PDF/DSC_GS15_ANT_manual.pdf with it? I have the correct connector.

Thanks,
Jason
Replies: 6
Views: 270
Posted By Jrothwell

Thanks again for the reply. The device contacts...

Thanks again for the reply. The device contacts do not support a resistor, itís a cellular communicator. The communicator has a NO input that Iím connecting to. Iím guessing my only option is to...
Replies: 6
Views: 270
Posted By Jrothwell

Thanks. I have several 4204s but they do not...

Thanks. I have several 4204s but they do not supervise the wire. What youíre describing as a workaround is the only thing I can think of as well. Using another relay that the 4204CF will apply and...
Replies: 6
Views: 270
Posted By Jrothwell

Vista 32fb and 4204CF

Hello,

Iím trying to have the 4204CF activate a zone on another system. I want the wire supervised so I figured the 4204CF would be the best choice. When I connect it to the zone terminals, the...
Replies: 9
Views: 544
Posted By Jrothwell

Thank you. Any other suggestions? Not sure what...

Thank you. Any other suggestions? Not sure what else to do.
Jason
Replies: 9
Views: 544
Posted By Jrothwell

That makes sense, but there is no ADT branding...

That makes sense, but there is no ADT branding anywhere on it. I can tell the difference between the ADT branded 20p systems but this one looks to be a standard Honeywell. The chip says...
Replies: 9
Views: 544
Posted By Jrothwell

Additionally, every installation manual I can...

Additionally, every installation manual I can find online for the FSA and the panel specifies an address between 8 and 23. The manual that came with the 2 modules states addresses between 00 and 04....
Replies: 9
Views: 544
Posted By Jrothwell

I just double checked everything and same result....

I just double checked everything and same result.
WAVIS32FB-15.5 2014 REV 5.5.
DEVICE TYPE Reserved 8.
Replies: 9
Views: 544
Posted By Jrothwell

Hmmmm. Thanks for the reply. Iím completely...

Hmmmm. Thanks for the reply. Iím completely confused then. I bought 2 FSA modules and a keyswitch. Everything says I should be able to program them and they are compatible but itís like FSA options...
Replies: 9
Views: 544
Posted By Jrothwell

Vista 32fb rev5.5 and FSA programming

Hello,

I am having trouble programming an FSA module into a vista 32fb panel. Some directions say to use device type 8, but when I choose this it says ďreservedĒ instead of ďfire displayĒ. Other...
Replies: 1
Views: 508
Posted By Jrothwell

Connect a NC magnetic contact to multiple systems

I am looking to use the same door contact to connect to an access control system as well as a security system. Is this possible without getting a relay involved?

Thanks
Replies: 6
Views: 1,124
Posted By Jrothwell

I resolved the issue. I had to change a parameter...

I resolved the issue. I had to change a parameter in the ZT90 configuration. Works as desired now, NC, no EOL.
Replies: 6
Views: 1,124
Posted By Jrothwell

No. All of the devices on the expansion module...

No. All of the devices on the expansion module are NC and the dip switches are set to NC, not EOL.
Replies: 6
Views: 1,124
Posted By Jrothwell

Zones 9-16 were deleted from the system before...

Zones 9-16 were deleted from the system before the expansion module was installed and addressed. They are programmed as Aux Wire. If I change the zones to anything other than zone type 90, they work...
Replies: 6
Views: 1,124
Posted By Jrothwell

Vista 20p 4219 expansion module and custom zone type 90

I assigned a zone on the 4219 as zone type 90. This zone type works fine on an RF zone or one of the 8 on-board zones, but on one of the 4219 zones, it just does nothing. If I change the zone type to...
Replies: 4
Views: 1,149
Posted By Jrothwell

Ok, understood...thank you!

Ok, understood...thank you!
Replies: 4
Views: 1,149
Posted By Jrothwell

Thanks but I use night stay when I'm sleeping and...

Thanks but I use night stay when I'm sleeping and have every zone active except for the bedroom motion detector.
Replies: 4
Views: 1,149
Posted By Jrothwell

Vista 20p interior follower question

I am looking to only have motion detectors only in the path to the keypad interior followers. What zone type would I assign the other motion detectors not in the path to the keypad? I'd like them to...
Replies: 5
Views: 847
Posted By Jrothwell

I am getting a NAC power supply for this that's...

I am getting a NAC power supply for this that's compatable with the horn/strobes and will provide supervision. However, I just came across the 4204cf; a supervised NAC output relay. I'm just curious...
Replies: 5
Views: 595
Posted By Jrothwell

Thank you. What do you mean by output connector?...

Thank you. What do you mean by output connector? The auxiliary power output?
Replies: 5
Views: 595
Posted By Jrothwell

Vista 20p sounder output question

Strange request...is there a way to make the sounder output (terminal 3) steady for fire alarms instead of pulsed? I am using relays to different devices and need continuous for fire and burg. Thanks
Replies: 5
Views: 847
Posted By Jrothwell

Does anyone have any more information on this?...

Does anyone have any more information on this? Thanks.
Replies: 5
Views: 847
Posted By Jrothwell

This is for a residential installation. The owner...

This is for a residential installation. The owner has horn strobes connected to the vista 20p and activated by a relay. I wanted to see if there was a way to "supervise" the loop of them by some...
Replies: 5
Views: 847
Posted By Jrothwell

Vista 20p notification appliance supervision

I have a vista 20p with a relay connected to a Wheelock strobe sync module then going out to 5 horn/strobes. There must be a way to supervise them. I was thinking with maybe another relay, EOLR and...
Showing results 1 to 25 of 59
 


 
Forum Jump