Search: Posts Made By: Davis_NF
Showing results 1 to 13 of 13
Search took 0.01 seconds.
Replies: 3
Views: 2,796
Posted By Davis_NF

thanks! rail will be 36" high. Davis

thanks! rail will be 36" high.


Davis
Replies: 3
Views: 2,796
Posted By Davis_NF

baluster spacing spcs for railings

I am re-building my raised deck - I need to know the maximum spacing requirements for balusters on the rails. The deck is about 5' above grade.

Thanks in advance
Replies: 10
Views: 5,083
Posted By Davis_NF

Hey Fish, I am having the same problem...

Hey Fish, I am having the same problem identifying the model number which has worn off of my machine.

it too is a Craftsman II, 8hp tecumseh, 24" cut
model number begins with either C93 or C83...
Replies: 10
Views: 10,343
Posted By Davis_NF

Hey Fish, I am having the same problem...

Hey Fish, I am having the same problem identifying the model number which has worn off of my machine.

it too is a Craftsman II, 8hp tecumseh, 24" cut
model number begins with either C93 or C83...
12-07-06, 05:59 AM
Replies: 2
Views: 19,600
Posted By Davis_NF

Outside lights Flickering

New Detached garage built last summer.

Electrical installed by certified Electrician with permit and inspections by the City.

Main power source to garage is from a 30amp two pole Circuit on...
Replies: 3
Views: 1,374
Posted By Davis_NF

no voltage on the humidistat leads. model NO...

no voltage on the humidistat leads.

model NO 200max... or is it max200....
Replies: 3
Views: 1,374
Posted By Davis_NF

Heat Recovery Ventilator problem

I have a "LifeBreath" HRV. seems as though the low voltage wall mounted humidistat was shorted out, and now the unit will not work.

the short did not cause a trip in power at the panel, and when...
Replies: 4
Views: 8,234
Posted By Davis_NF

Everything is fine now. I removed the idler...

Everything is fine now.

I removed the idler pulley and re-installed. I guess-timated the offset for the guide pins and Sounds as though I got it right. Thanks for the confirmation puey.:thumbup:...
Replies: 4
Views: 8,234
Posted By Davis_NF

Craftsman Tecumseh 8/25 Snowblower throwing Auger Belt

Hi all,

I have a Craftsman 8hp 25" cut snowblower with tecumseh engine., circa 1990.

It blew the auger belt yesterday. I picked up a new one (local service shop supplied me with murray part #...
Replies: 3
Views: 14,335
Posted By Davis_NF

I had inner tubes put in mine two years ago and...

I had inner tubes put in mine two years ago and haven't had any problems since.
Replies: 8
Views: 12,051
Posted By Davis_NF

I just built a small garage last summer. For a...

I just built a small garage last summer. For a work bench I acquired a free standing kitchen cabinet base froma co-worker that was doing a kitchen renno... very sturdy, I've atached 4" vise to it,...
Replies: 3
Views: 1,984
Posted By Davis_NF

Does that car have two seprate iginition control...

Does that car have two seprate iginition control modules...? if so, one may be troast, and you could be running on one module alone. Should be an easy swap, but the module may be a bit pricey.
Replies: 3
Views: 2,790
Posted By Davis_NF

Click Here...

Click Here (http://i25.photobucket.com/albums/c92/CabbyShack/snowblower/DSC00923.jpg) for a pic of a Carb on an 8hp Tecumseh Snowblower motor. I am not sure if the throttle linkage you're looking...
Showing results 1 to 13 of 13


 
Forum Jump