Search: Posts Made By: jrsick
Showing results 1 to 13 of 13
Search took 0.02 seconds.
04-12-21, 02:55 PM
Replies: 6
Views: 132
Posted By jrsick

You may also want to look at bull nose tile, to...

You may also want to look at bull nose tile, to include quarter bull nose and half bull nose. These may provide the transition you are looking for.
Replies: 13
Views: 266
Posted By jrsick

We'll have to agree to disagree on this topic...

We'll have to agree to disagree on this topic marq1. I maintain that brakes turn the kinetic energy of the car motion to thermal energy at the brake components. The faster you can transfer heat the...
Replies: 12
Views: 289
Posted By jrsick

Do you know yet what work will be done? engine...

Do you know yet what work will be done? engine in or out? Just replace rings without hone/bore, hone only, or bore? What size engine?
There will be other problems found when you/mechanic get...
04-05-21, 09:46 AM
Replies: 6
Views: 218
Posted By jrsick

All good comments so far. Another option is to...

All good comments so far. Another option is to sand down the sill to bare wood, coat with a wood petrifier like PC Woody or Abatron, then paint. The petrifier will convert the wood to a hard,...
Replies: 16
Views: 333
Posted By jrsick

You should also take a good look at the roof...

You should also take a good look at the roof sheathing and mark all of the soft spots. These are areas you'll need to replace, and, do not want to step on.
Definitely rip off the old shingles and...
Replies: 5
Views: 159
Posted By jrsick

Top dead center, that's when the piston is at...

Top dead center, that's when the piston is at it's highest point in the cylinder.
Usually that 1366 code means that you need to replace the crankshaft position sensor (aka the TDC sensor). Fairly...
Replies: 6
Views: 142
Posted By jrsick

DA is dual action. DA polishers move the pad...

DA is dual action. DA polishers move the pad side to side very quickly and are intended to mimic hand application. DA polishers are good for small scratches or bringing out the shine in paint that...
Replies: 1
Views: 162
Posted By jrsick

If air was only cold when car was moving, it...

If air was only cold when car was moving, it could be because your ac condenser fan needs to be replaced. Turn on your ac and see if the condenser fan comes on.
To charge your ac with...
03-02-21, 02:55 PM
Replies: 6
Views: 203
Posted By jrsick

Have you checked the pump cover for cracks? How...

Have you checked the pump cover for cracks? How about the drain plugs on the pump case? Some have had success putting shaving cream around suspected leak areas.
For the valves, you could try...
Replies: 9
Views: 285
Posted By jrsick

A wire saw or cable saw might work well here...

A wire saw or cable saw might work well here also.
Believe it or not, dental floss is surprisingly good in these applications sometimes.
02-01-21, 05:57 AM
Replies: 7
Views: 264
Posted By jrsick

Also check the position of the hot water valve...

Also check the position of the hot water valve under the sink. Make sure it is fully open. Check that the valves under all sinks and washing machine are full open.
01-23-21, 04:48 AM
Replies: 5
Views: 302
Posted By jrsick

I have had great results from Advance Carpenter...

I have had great results from Advance Carpenter Ant bait. It's a protein bait and the ants will always want it. Terro is sweet-based and the ants only want it at certain times. I've also heard...
01-19-21, 04:53 AM
Replies: 19
Views: 525
Posted By jrsick

I agree with Lakeseed that the window looks...

I agree with Lakeseed that the window looks suspect. The grade slopes from the window to the entry point, so water would flow from the window to the water entry point inside your home. The water...
Showing results 1 to 13 of 13


 
Forum Jump