Search: Posts Made By: prh129
Showing results 1 to 12 of 12
Search took 0.01 seconds.
08-17-06, 08:53 AM
Replies: 2
Views: 3,105
Posted By prh129

I think you have the right idea with the control...

I think you have the right idea with the control board - I have found that the problem occurs when I have the temp set to 72 but if I bump it up to 74, the compressor seems to come on.

I don't...
07-14-06, 07:13 PM
Replies: 2
Views: 3,105
Posted By prh129

Whirlpool A/C Compressor Won't Start

I have an ACQ158XL 15000 BTU window AC that I just put in this morning. The fan ran but the compressor would not start - the fan would run for about 10 seconds then shut off then try again. After...
04-19-06, 11:23 AM
Replies: 15
Views: 18,460
Posted By prh129

I checked it out again last night (the...

I checked it out again last night (the installation manual does show how to switch the unit to meter mode) and the gallon reading did not change after leaving the water running for several minutes. I...
04-18-06, 02:22 PM
Replies: 15
Views: 18,460
Posted By prh129

Now that I know about the Iron Out (and have...

Now that I know about the Iron Out (and have some) I will use it regularly. I had cleaned out the brine tank several years ago and I plan to let the salt run down and clean it out again soon.

I...
04-18-06, 09:31 AM
Replies: 15
Views: 18,460
Posted By prh129

With the water meter, it seemed I was going about...

With the water meter, it seemed I was going about two weeks between regenerations (the last time I was monitoring it). I started with a setting of 10 days for now.

It seems odd as I could have...
04-17-06, 12:02 PM
Replies: 15
Views: 18,460
Posted By prh129

The service guy came today. He found that the...

The service guy came today. He found that the flow meter wasn't working and also installed an eductor service kit which had a bunch of parts including the screen I had cleaned. This seemed to solve...
04-06-06, 03:40 PM
Replies: 15
Views: 18,460
Posted By prh129

The water tests from 1996 showed iron from 0.5 to...

The water tests from 1996 showed iron from 0.5 to 1.1 ppm.

I would like to replace the screen. It sounds like the service pack that Biff mentioned contains a lot of the parts that would typically...
04-06-06, 06:34 AM
Replies: 15
Views: 18,460
Posted By prh129

Well I made some progress - I found the parts...

Well I made some progress - I found the parts list for the softener and located the injector and screen. There is a metal plate on the top of the head. After moving the valve into the bypass...
04-06-06, 06:24 AM
Replies: 25
Views: 40,171
Posted By prh129

Biff, Do you know what the part number is...

Biff,

Do you know what the part number is for the Mark 100 update kit? Also, did it come with instructions? Thanks.

Peter
04-04-06, 08:46 AM
Replies: 15
Views: 18,460
Posted By prh129

Last night I removed the float assembly from the...

Last night I removed the float assembly from the brine tank to check for a blockage. I rinsed it off and was able to blow air through it. I reconnected it and ran another regen cycle. During the...
04-03-06, 02:58 PM
Replies: 15
Views: 18,460
Posted By prh129

Yes, I did wait several hours. First I removed a...

Yes, I did wait several hours. First I removed a bucket's worth of salt then pulled the remaining salt to one side of the tank so that the brine solution was visible on the other side. This way I...
04-03-06, 10:24 AM
Replies: 15
Views: 18,460
Posted By prh129

Question Culligan Mark 100 Venturi Cleaning Help?

I have a Culligan Mark 100 water softener (10 years old) that isn't using any salt. I made sure that there was no salt bridging and ran two regeneration cycles. It looked like so salt water was being...
Showing results 1 to 12 of 12


 
Forum Jump