Search: Posts Made By: phyberoptic
Showing results 1 to 15 of 15
Search took 0.01 seconds.
03-23-14, 08:46 PM
Replies: 9
Views: 913
Posted By phyberoptic

You should be able to push the remains of the...

You should be able to push the remains of the plug through the back of the jack with a thin long screwdriver. unplug the power first of course. the plug remains should fall to the bottom of the amp ...
Replies: 10
Views: 1,652
Posted By phyberoptic

I'd just use wifi and be done. With the speeds of...

I'd just use wifi and be done. With the speeds of the newest equipment most home needs are satisfied quite well with wireless.
-=Phyber.
Replies: 3
Views: 1,009
Posted By phyberoptic

Pick up a wireless bridge for the shed. It will...

Pick up a wireless bridge for the shed. It will act as a remote station and talk over wifi to the home router. You may need a "patch" antenna on it that will face toward the home wireless router to...
03-22-14, 09:11 PM
Replies: 23
Views: 3,916
Posted By phyberoptic

Except that maximum width of an RV/trailer is...

Except that maximum width of an RV/trailer is 8'6".
-=Phyber
03-22-14, 08:53 PM
Replies: 17
Views: 1,574
Posted By phyberoptic

I'd argue the safety equivalence of the two...

I'd argue the safety equivalence of the two solutions. And the code compliancy as well, but that's been done all over the internet already. I was just passing on what worked for me, and it is a much...
03-22-14, 08:33 PM
Replies: 3
Views: 687
Posted By phyberoptic

Sorry but just because someone else did the...

Sorry but just because someone else did the ghetto work doesn't make it ok. And since you are now modding that work you need to make it right... (up to code).

-=Phyber
03-22-14, 08:22 PM
Replies: 17
Views: 1,574
Posted By phyberoptic

I was given one of those transfer panels with the...

I was given one of those transfer panels with the 10 circuits to choose and wire... It's still in the box. I put an interlock on the load center and a 50amp breaker to accept the generator plug. I...
03-22-14, 08:14 PM
Replies: 7
Views: 3,367
Posted By phyberoptic

Bah, a 20 amp breaker will be fine for a...

Bah, a 20 amp breaker will be fine for a dedicated line. Clamp on an amp meter with it running and you won't see near 15 amps steady state. There is probably a jumper on the compressor if you want...
03-22-14, 08:07 PM
Replies: 7
Views: 941
Posted By phyberoptic

You lost a leg of the service... the up and down...

You lost a leg of the service... the up and down associated with the power company work must have stress the final wires that were providing service and they gave. You may read low voltage on that...
03-21-14, 07:58 PM
Replies: 23
Views: 3,916
Posted By phyberoptic

If you keep the shed to 100 SQFT (OR 120 SQFT in...

If you keep the shed to 100 SQFT (OR 120 SQFT in some areas - check with your building dept), you'll not need a permit for the shed.
03-21-14, 03:28 PM
Replies: 9
Views: 1,053
Posted By phyberoptic

The transition from 6-3 NMB to individual THWN...

The transition from 6-3 NMB to individual THWN conductors is done how? In a box using wire nuts?
-=Phyber
03-20-14, 08:36 PM
Replies: 9
Views: 1,053
Posted By phyberoptic

If I run individual wires, they can go in the...

If I run individual wires, they can go in the underground conduit?

But they will also need to be in conduit through the garage to the basement load center?

-=Phyber
03-20-14, 08:33 PM
Replies: 9
Views: 1,053
Posted By phyberoptic

So I can run 6-3 UF-B W/G from the new load...

So I can run 6-3 UF-B W/G from the new load center through the conduit into the garage, and then exposed through the garage into the basement load center?

-=Phyber
03-20-14, 08:05 PM
Replies: 3
Views: 704
Posted By phyberoptic

They should have never tiled onto the sheetrock...

They should have never tiled onto the sheetrock in the first place. +1 on removal and replacement with cement board before tiling. Also, if this is near a sink or water source, I'd seal the...
03-20-14, 07:48 PM
Replies: 9
Views: 1,053
Posted By phyberoptic

Wiring a new shop

Finished building a 900 sqft shop detached and about 12 ft. away from the main garage. Id like to get a sanity check on my plans to wire the electrical and choice of load center for the shop.
My...
Showing results 1 to 15 of 15


 
Forum Jump