Search: Posts Made By: twood020
Showing results 1 to 12 of 12
Search took 0.01 seconds.
08-01-16, 07:01 AM
Replies: 5
Views: 1,034
Posted By twood020

Thanks for the quick replies! I was planning on...

Thanks for the quick replies! I was planning on shimming out the header with 2x4s laid flat against the header, to give a cavity for the wire, and also the ability to Sheetrock over it. I can't...
07-31-16, 11:19 PM
Replies: 5
Views: 1,034
Posted By twood020

Boring Hole in staircase 2x10s

Hi All!

I've had great luck with advice on these forums, so i figured why quit now. My latest question is in regards to holes bored in joists. I'm not sure of the correct terminology, but this...
06-08-16, 08:29 PM
Replies: 3
Views: 10,265
Posted By twood020

Thanks for the quick reply, excellent...

Thanks for the quick reply, excellent response...and thanks for the blessing lol. Just to be safe, even if it were load bearing, removing that stud and replacing with a properly sized doubled up...
06-08-16, 08:02 PM
Replies: 3
Views: 10,265
Posted By twood020

Identiying Load Bearing Wall for Stud Removal

Hi All!

So I know that it's possible to remove a single stud from a load bearing wall, given proper replacement with jack studs, header, cripples, etc... However I'd like to identify first if the...
Replies: 2
Views: 3,961
Posted By twood020

Building Out Deck to Meet Retaining Wall

Hi All,

I've always had good luck on these forums, so I'll pick your brains again about an issue I've run into.
I'm extending an existing Trex deck to meet up with a concrete retaining wall,...
Replies: 7
Views: 11,577
Posted By twood020

Seafoam did the trick!! Did it exactly as...

Seafoam did the trick!! Did it exactly as described, after initial 10 minute run it had already cleared up. Amazing stuff, thanks again for the quick responses.
Replies: 7
Views: 11,577
Posted By twood020

Thanks for the feedback guys, I'll try it out...

Thanks for the feedback guys, I'll try it out this weekend. Hopefully the SeaFoam works, never disassembled a carb before. Much appreciated.
Replies: 7
Views: 11,577
Posted By twood020

Generac GP6500 generator surging "hunting" while idle.

I have a Generac GP6500 generator that's surging while idle. It has 4.5 hours on it. I've run it for 10 minutes every month. This started last month, I just tried draining all fuel, removed the...
Replies: 5
Views: 2,055
Posted By twood020

Thanks PJ, I think I'll just swap out one of...

Thanks PJ, I think I'll just swap out one of those dimmers for a switch. Other than that do either, or both, look acceptable, based on 2005 NEC codes?
Replies: 5
Views: 2,055
Posted By twood020

Thanks Ray for the quick response! The only...

Thanks Ray for the quick response!

The only wire that's actually already pulled is the feed from the breaker to that ceiling box and the 2 gang switch box is another 15+ feet away, ugh. So I...
Replies: 5
Views: 2,055
Posted By twood020

Running new circuit w/ switch for 1 light and 2 dimmers for ceiling lights

Hi guys,

I have relatively little experience doing electrical work around my house (changing switches, adding/changing outlets/light fixtures, etc). Im starting a new project in the basement,...
Replies: 1
Views: 3,871
Posted By twood020

WATTS Backflow Preventer leaking

Hi,

I should start off by saying I'm a very amateur DIY'er, but not afraid to roll up my sleeves and attempt DIY jobs.

I have a Weil Mclain wtgo-4, oil fired boiler, with a 1/2 9D-M3 WATTS...
Showing results 1 to 12 of 12


 
Forum Jump