Search: Posts Made By: nbmech
Showing results 1 to 25 of 51
Search took 0.01 seconds.
Replies: 7
Views: 2,329
Posted By nbmech

thanks for the tips. I have started to use the...

thanks for the tips. I have started to use the high temp cycle and it seems to be doing better.
Replies: 7
Views: 2,329
Posted By nbmech

OK the drain hose goes up and touches the bottom...

OK the drain hose goes up and touches the bottom of the countertop then to the sink drain. We don't have a disposal.
Replies: 7
Views: 2,329
Posted By nbmech

OK Thanks, I just used the old drain line from my...

OK Thanks, I just used the old drain line from my old dishwasher as it was easier than running the new drain. It does go up to the bottom of the countertop. Possibly the hose diameter is different...
Replies: 7
Views: 2,329
Posted By nbmech

Kenmore dishwasher not cleaning well

Hi,
My newly installed dishwasher is not cleaning well. There has been food left on glasses and silverware almost every time we have used it. We started by using the Smart wash and have changed to...
Replies: 2
Views: 806
Posted By nbmech

Moen camerist loose handle

Hi,
My single handle kitchen faucet keeps coming loose. I tighten the set screw repeatedly and within a week the handle is loose. I even ordered a new handle and it is loose within two days!!! Any...
Replies: 2
Views: 592
Posted By nbmech

Loose undercounter dishwasher

Hi,

My dishwasher has become loose from the countertop. I think the steam vent has made the countertop soft above the vent. Any ideas hot to reattach the bracket?
Thanks
Replies: 9
Views: 2,037
Posted By nbmech

I think it was the clutch. I replaced it and it...

I think it was the clutch. I replaced it and it seems to be working again. Thanks all who offered help.
Replies: 9
Views: 2,037
Posted By nbmech

it drains, it just doesn't spin every time,

it drains, it just doesn't spin every time,
Replies: 9
Views: 2,037
Posted By nbmech

Thanks for the help. Finally had time to...

Thanks for the help.

Finally had time to look at it again, The screws were loose and I tightened them. The washer goes through all the cycles and the motor runs but the tub still doesn't spin. So...
Replies: 9
Views: 2,037
Posted By nbmech

Wow that was quick! Model # 110.26862503. ...

Wow that was quick!

Model # 110.26862503. I already replaced the lid switch. It was somehow broken, probably from slamming the lid down. The lid seems a little loose???
Replies: 9
Views: 2,037
Posted By nbmech

Kenmore 80 washer sometimes not spinning

Hi,

My Kenmore series 80 washer is not always spinning. Sometimes I can correct it by slamming the lid down. Other times I rotate the inside of the washer a little and as a last resort I need to...
Replies: 3
Views: 725
Posted By nbmech

Thanks for responding. I have hot water heat and...

Thanks for responding. I have hot water heat and no A/C. There is no air movement there. The only opening is to the finished basement and is hidden behind a picture.
Replies: 3
Views: 725
Posted By nbmech

crawl space moisture

Hi,

I need some advice for controlling moisture in my crawlspace. I live in Northeast Ohio. Cold dry winters and warm humid summers. I have a 25' x 25' crawlspace with a poured concrete floor. I...
Replies: 2
Views: 663
Posted By nbmech

GE oven baking element

Hi,

The bottom element on my GE JBP35DOK1WW oven turned bright red and actually had a small flame on it yesterday. Now the oven wont heat up. I have searched for the part number but the model...
Replies: 10
Views: 4,587
Posted By nbmech

Thanks for the help. Here is a copy f...

Thanks for the help.



Here is a copy f the diagram provided with the unit.


The zone valve has markings TH/TR, TH and TR
Replies: 10
Views: 4,587
Posted By nbmech

thermostat wiring

Hi,

I would like to install a Dayton 1UHG7 wireless thermostat for my hot water baseboard system. I need to connect the thermostat to a Honeywell V8043 zone valve. The other hardwired zones...
Replies: 1
Views: 814
Posted By nbmech

kenmore 665.1652000 dishwasher

Hello, My kenmore 665.1652000 dishwasher ran a cycle last night but the rinse didnt work. I remember hearing the pump running louder than normal but didnt think much about it. When my wife checked...
Replies: 7
Views: 5,447
Posted By nbmech

I guess I could jump the test points on the...

I guess I could jump the test points on the control head and check the voltage at the selonoid.
Replies: 7
Views: 5,447
Posted By nbmech

Thank you. Update I used a hair dryer...

Thank you.

Update

I used a hair dryer to melt the ice in the chute to the ice tray. It seemed to work fine for a day or two, full bin of ice. There is no ice buildup in the chute. Now the...
Replies: 7
Views: 5,447
Posted By nbmech

its a Kenmore 106.74232402 ice maker ...

its a Kenmore 106.74232402

ice maker 106.62636
Replies: 7
Views: 5,447
Posted By nbmech

Thanks for the reply. The tray is not...

Thanks for the reply.
The tray is not overfilling just not dumping and ice buildup in the filler tube.
Replies: 7
Views: 5,447
Posted By nbmech

frozen ice maker fill tube

Hello,

My ice maker fill tube is filling with ice!!! The ice mold is full and the ice chunk continues to the tube. I have had to remove the unit to thaw it out. It worked fine overnight but then...
Replies: 3
Views: 2,759
Posted By nbmech

it's about 2" thick and dry stacked

it's about 2" thick and dry stacked
Replies: 3
Views: 2,759
Posted By nbmech

loose stone veneer on house

Hello,
What is the best way to reattach stone veneer that has fallen off around the doorway on my front porch?

Liquid Nails or some type of tube adhesive or must I try to re mortar it in...
Replies: 6
Views: 1,372
Posted By nbmech

Thanks for the info. Adding baseboard would be...

Thanks for the info. Adding baseboard would be easier.

They are in the middle of the loop, a 10 by 13 bedroom has a 10 foot section of baseboard. The house was built in the mid 60's with only...
Showing results 1 to 25 of 51
 


 
Forum Jump