Search: Posts Made By: stacia
Showing results 1 to 16 of 16
Search took 0.01 seconds.
01-14-19, 02:11 AM
Replies: 3
Views: 997
Posted By stacia

We've already replaced the ignition control...

We've already replaced the ignition control panel, which has fixed the problem.

The furnace was looked over by an HVAC company in October. We have someone come out every year to check it in the...
01-02-19, 02:55 PM
Replies: 3
Views: 997
Posted By stacia

Lennox Whisper Heat G20 ignition panel problem again

Hi all -- we have a consistent problem with our furnace with the ignition panel breaking every few years, causing our burners to fail to light sometimes. It's a Lennox Whisper Heat G20, original to...
Replies: 21
Views: 14,652
Posted By stacia

Great idea about the mousetraps, Bud, thanks!...

Great idea about the mousetraps, Bud, thanks! We'll get some up there ASAP. We've discussed the fiber optic camera but my husband is kind of wary of it. "If there's a rip I'll have to get over there...
Replies: 21
Views: 14,652
Posted By stacia

I hope it's not critters, but we haven't been...

I hope it's not critters, but we haven't been able to tell yet!

My husband got up into the crawl space and discovered that all of the flex ductwork is in one location, piled one on top of the...
07-16-15, 11:17 AM
Replies: 3
Views: 1,054
Posted By stacia

Yes, the outside unit is running fine, though I...

Yes, the outside unit is running fine, though I don't think the condenser is running. It doesn't sound like it, at any rate.

I'll try jumping those wires and see what happens, thanks for the...
07-16-15, 10:33 AM
Replies: 3
Views: 1,054
Posted By stacia

No Cold Air from Central A/C - Possible Thermostat Problem?

I've been posting on another thread about some duct work that I think has a hole in it, but now I have a new problem - no cold air from the a/c.

Our central air conditioner stopped putting out...
Replies: 21
Views: 14,652
Posted By stacia

We weren't able to visualize anything wrong with...

We weren't able to visualize anything wrong with the flexible ductwork but weren't able to get as close as we wanted, because we didn't have enough plastic sheeting or more boards to allow us to...
Replies: 21
Views: 14,652
Posted By stacia

Hi Furd -- There is a gap but we checked around...

Hi Furd -- There is a gap but we checked around it and didn't find anything that looked like the insulation. We closed the gap some and put the vent back in, and there's new insulation caught in the...
Replies: 21
Views: 14,652
Posted By stacia

Hey airman -- yes, the duct coming up off the AHU...

Hey airman -- yes, the duct coming up off the AHU is metal. It looks as though just past the ceiling it joins up with another metal duct going left to right.
Replies: 21
Views: 14,652
Posted By stacia

Okay, sorry for the delay in replying. Our...

Okay, sorry for the delay in replying.

Our duct in the kitchen is metal for about 18 inches with a sharp, almost 90 degree angle immediately past the vent, then connects to flexible ductwork with...
Replies: 21
Views: 14,652
Posted By stacia

I was sure it was metal but I texted my husband...

I was sure it was metal but I texted my husband and he said it might be duct board, so he'll check tonight after he gets home.
Replies: 21
Views: 14,652
Posted By stacia

Yellow Fluffy Insulation Coming Out of HVAC Vents

I'm hoping someone can help me figure out where to start with this problem.

In the kitchen (and only the kitchen) there have been a few small tufts of what looked like yellow lint for about a...
02-21-14, 07:25 AM
Replies: 6
Views: 2,667
Posted By stacia

We just had the ignition control panel replaced....

We just had the ignition control panel replaced. The one they installed in Nov 2008 was a Honeywell, which was working off and on -- it hadn't completely gone bad and had just run for 26 hours...
02-19-14, 08:53 AM
Replies: 6
Views: 2,667
Posted By stacia

I completely forgot to ask which module it was --...

I completely forgot to ask which module it was -- sorry! But the repair place came out this morning and verified it IS the ignition control panel.

Johnson is the original brand that this came...
02-17-14, 09:36 PM
Replies: 6
Views: 2,667
Posted By stacia

Looks like the repair place can't get out here...

Looks like the repair place can't get out here until Wednesday morning - any thoughts you have would be most welcome! The furnace will work for hours but then goes out again, and takes all night to...
02-17-14, 02:04 AM
Replies: 6
Views: 2,667
Posted By stacia

Lennox WhisperHeat G20 burners only working part of the time

We have a Lennox WhisperHeat G20 Q2E50-4 furnace from approximately 1994, when the house was built. For a couple of days, we've noticed the furnace will kick on and run for about 2 minutes, then...
Showing results 1 to 16 of 16


 
Forum Jump