Search: Posts Made By: snowdrift
Showing results 1 to 11 of 11
Search took 0.01 seconds.
02-18-11, 05:20 AM
Replies: 19
Views: 3,143
Posted By snowdrift

I pulled out the switch, which is pretty small,...

I pulled out the switch, which is pretty small, and then realized that the center of this small cylindrical part has a tiny button that can be pushed in, like a switch. I did that, and checked...
02-17-11, 08:23 AM
Replies: 19
Views: 3,143
Posted By snowdrift

Grady said this: "...That pink wire goes thru...

Grady said this: "...That pink wire goes thru several switches. Set your meter for continuity & check each of those switches. They should all be closed (having continuity thru them)."

That's...
02-16-11, 08:20 PM
Replies: 19
Views: 3,143
Posted By snowdrift

Guys, I just might have found the culprit. One of...

Guys, I just might have found the culprit. One of the switches shows no ohm reading (shows 0.L). So where do I buy one of these suckers? Does Depot/Lowes carry them?

Thanks!
02-13-11, 12:59 PM
Replies: 19
Views: 3,143
Posted By snowdrift

The model is Janitrol GMPN060-3.

The model is Janitrol GMPN060-3.
02-12-11, 02:03 PM
Replies: 19
Views: 3,143
Posted By snowdrift

Yes, we have a separate gas furnace for the...

Yes, we have a separate gas furnace for the upstairs and it's working fine.

Finally got the voltages, and they don't look too promising. The wires are so close together (plugged into the gas...
02-11-11, 02:14 PM
Replies: 19
Views: 3,143
Posted By snowdrift

Hi Grady/SP, I timed the events: Time from...

Hi Grady/SP, I timed the events:

Time from "click" to start ignitor to the "click" to stop ignitor = 13-14 seconds (this is when the ignitor is glowing)

Time from "click" to stop ignitor to the...
02-10-11, 09:08 PM
Replies: 19
Views: 3,143
Posted By snowdrift

Sure thing. I don't have a multimeter, so that...

Sure thing. I don't have a multimeter, so that will give me time to get one. I truely appreciate the concern and help.
02-10-11, 08:45 PM
Replies: 19
Views: 3,143
Posted By snowdrift

I was wrong about the click. Every time the...

I was wrong about the click. Every time the ignitor kicks in AND shuts down, there is a click. Also, the model# is GMPN060-3. While I was there, I also checked "venter pressure switch" (the rubber...
02-10-11, 08:23 PM
Replies: 19
Views: 3,143
Posted By snowdrift

No click when the ignitor shuts down. The red...

No click when the ignitor shuts down. The red light on the control board is lighted solid throughout the process. I'll check the model in a minute...
02-10-11, 08:05 PM
Replies: 19
Views: 3,143
Posted By snowdrift

gas furnace not working

My janitrol gas furnace isn't working. The draft inducer motor starts, then the hot surface ignitor glows for about 10 seconds and goes dull. It glows again after a minute and again goes dull. After...
02-10-11, 07:50 PM
Replies: 3
Views: 1,632
Posted By snowdrift

janitrol gas furnace burners not coming on

my janitrol gas furnace isn't working. The draft inducer motor starts, then the hot surface ignitor glows for about 10 seconds and goes dull. It glows again after a minute and again goes dull. After...
Showing results 1 to 11 of 11


 
Forum Jump