Search: Posts Made By: hgiljr
Showing results 1 to 17 of 17
Search took 0.02 seconds.
Replies: 7
Views: 11,229
Posted By hgiljr

Which tubbing are you referring to? Can you...

Which tubbing are you referring to? Can you attach a picture? I did replace the gasket on the intake side of the carb and o ring on the side of carb to motor. Thanks for info
Replies: 7
Views: 11,229
Posted By hgiljr

Actually for me I had no winter storage as I live...

Actually for me I had no winter storage as I live down here in SFLA and mowed the lawn at least once a week... In regards to the misfire, one thing I did yesterday that I read on another forum was...
Replies: 7
Views: 11,229
Posted By hgiljr

Craftsman / Briggs engine misfire

Hello all. I have a Craftsman model 917370561 lawn mower with a briggs stratton engine. It began misfiring, so I gave it a tune up (change oil, filter and spark plug). It continued misfiring and...
Replies: 7
Views: 5,327
Posted By hgiljr

Yes both are Briggs Stratton engines on Craftsman...

Yes both are Briggs Stratton engines on Craftsman equipment. The engine with the 7/8 shaft is on the pressure cleaner and the 1 inch is on the lawn mower. Pressure Cleaner Sears model number is...
Replies: 7
Views: 5,327
Posted By hgiljr

Swapping engine shafts

Good day. I have a spare Briggs Stratton engine with a 7/8 vertical shaft. My lawn mower engine has a 1inch vertical shaft. I would like to swap engine as my the lawn mower engine is giving me...
Replies: 2
Views: 932
Posted By hgiljr

Craftsman pressure washer engine not turning

Hello all. So my pressure washer 3000 psi, began to lose pressure. I decided to take apart the pressure pump and found the problem. With pump removed I attempted to turn the engine with the pull...
08-05-11, 08:54 PM
Replies: 1
Views: 1,799
Posted By hgiljr

Compressor kickstart and time delay

Hello all. So today I had a start Time delay and kick start added to my compressor. Reason for time delay is because of the many power flickers we have in the area and kickstart since I was told it...
Replies: 1
Views: 866
Posted By hgiljr

Ceiling fan is slower on max speed then before

Hello. I have three outdoor ceiling fans and recently two are a bit slower then they originally where. In fact you can notice the slower speed when compared to the third fan. This all began when two...
Replies: 2
Views: 2,078
Posted By hgiljr

Best Door Lock for the money

Hello everyone. So looking at replacing the home's main entrance door lock. I was mainly thinking of Medeco since I was under the impression it couldn't be bumped, until I searched on youtube. All i...
Replies: 9
Views: 11,226
Posted By hgiljr

Cheese can you get me a link or picture of what...

Cheese can you get me a link or picture of what you mean so I can try to track one down? Thanks again
Replies: 9
Views: 11,226
Posted By hgiljr

Not sure on larger engines. On these small gas...

Not sure on larger engines. On these small gas engines all i know the idle screw is what is adjusted. Might want to contact the company to see what they say in your case...
Replies: 9
Views: 11,226
Posted By hgiljr

They have an adjusting screw of how much propane...

They have an adjusting screw of how much propane to pump into the engine so it can idle correctly. This is aside from the adjusting screw on the carb. If you go with a direct induction to the carb,...
Replies: 9
Views: 11,226
Posted By hgiljr

Engine Number or Engine Model #? If latter it is...

Engine Number or Engine Model #? If latter it is 210000: http://www.mymowerparts.com/pdf/Briggs%20&%20Stratton%20Replacement%20Engine%20Information/289700-MS2919-0404.pdf

If engine number is what...
Replies: 9
Views: 11,226
Posted By hgiljr

Tri-Gas Convert Kit on Briggs & Stratton Generator

Hello all. I am looking at adding the conversion kit for Tri-gas from:
Generator Conversion Kits to Propane and Natural Gas. (http://www.propane-generators.com/)
and their system works by adding an...
Replies: 2
Views: 713
Posted By hgiljr

You mean as the paint dries to hand throw some...

You mean as the paint dries to hand throw some sand so it can dry along with the paint or to mix the paint with some sand?
Replies: 2
Views: 713
Posted By hgiljr

Not sure what to do to my Concrete

Hello all... I am looking for help here. i have been doing a lot of reading regarding finishes for a Concrete Slab. I have about 500 sq ft of a concrete slab next to my home in the backyard that I...
Showing results 1 to 17 of 17


 
Forum Jump