Search: Posts Made By: BeerRidge
Showing results 1 to 13 of 13
Search took 0.01 seconds.
Replies: 4
Views: 488
Posted By BeerRidge

Thank you for the ideas so far. My basement is...

Thank you for the ideas so far. My basement is block as well and all on the same level. There's a sump pit and perimeter drain system (I'm told) but no mold issue that I see inside, just the garage....
Replies: 4
Views: 488
Posted By BeerRidge

Garage Help

Hello all
A couple weeks ago we had a lot of rain in the northeast. Our water table rose and I had a small amount of water come through my slab in the basement for the first time. My garage didn't...
01-02-17, 10:20 AM
Replies: 6
Views: 604
Posted By BeerRidge

Finishing block basement

Hello again,

Simple question this time. I plan to put cedar tongue and groove planks over my basement wall in a room I'm finishing. The block has the white moisture/mold resist paint on it and...
Replies: 4
Views: 899
Posted By BeerRidge

This is why I come here. You guys are always a...

This is why I come here. You guys are always a help! Thank you! I'll let you know if this doesn't fix me up.
Replies: 4
Views: 899
Posted By BeerRidge

Craftsman Air Compressor Issues

I have another issue I need your help with. I moved my Craftsman Air Compressor model 919.165610 from my old house to new. The wiring instruction states a dedicated 15amp circuit should work (240v,...
Replies: 9
Views: 3,359
Posted By BeerRidge

That sounds easier for the ceiling. My concern is...

That sounds easier for the ceiling. My concern is more for fireproofing and stability during a fire vs. security. My neighborhood is pretty safe with a lot of retired neighbors so I just want the...
Replies: 9
Views: 3,359
Posted By BeerRidge

It would be primarily for a large firearm...

It would be primarily for a large firearm collection. I cant keep buying more safes as the collection grows.
Replies: 9
Views: 3,359
Posted By BeerRidge

Adding block vault to existing basement?

I tried posting this in the interior forum but had no success so I will try here. I'm looking for advice and/or ideas on an upcoming project. I'm looking to add a vault to my basement. Maybe 12x8'...
11-25-15, 10:34 AM
Replies: 13
Views: 1,777
Posted By BeerRidge

Well the engineer was out this morning and gave...

Well the engineer was out this morning and gave me the news...The wall is not load bearing due to the fink style trusses and the wall in question is not located on one of the "V"s on the bottom cord...
11-23-15, 08:46 AM
Replies: 13
Views: 1,777
Posted By BeerRidge

I cut the hole but couldn't see the truss....

I cut the hole but couldn't see the truss. Obviously by the picture there's 2 top plates. I specifically cut the hole right next to the entrance in the wall which also sits directly above the...
11-20-15, 08:46 AM
Replies: 13
Views: 1,777
Posted By BeerRidge

Pics

Here are the best pics I could get with the low light and minimal space.
11-19-15, 05:13 AM
Replies: 13
Views: 1,777
Posted By BeerRidge

Excellect feedback guys! The 2 amateurs as I...

Excellect feedback guys! The 2 amateurs as I called them were my brother who went to a community school for construction, specialized in material estimating but has limited time in the field. The...
11-18-15, 07:26 PM
Replies: 13
Views: 1,777
Posted By BeerRidge

Wall removal/Header span?

Hello all, I'm new to the forum and lack an engineering degree for my upcoming remodel. Long story short, I'm looking to remove a non load bearing wall between my kitchen and living room. The home...
Showing results 1 to 13 of 13


 
Forum Jump